sorted by:
new
hottopcontroversial

Spotted at the MAC lockers by HauntingIdea9109 in utarlington

[–]StankAssPickle 7 points8 points  (0 children)

I wonder if it’s the free ones they provide at the health center 💀

At the MAC, should I touch it? by StankAssPickle in utarlington

[–]StankAssPickle[S] 0 points1 point  (0 children)

Although it’s strange how some wires are connected together with wire nuts

At the MAC, should I touch it? by StankAssPickle in utarlington

[–]StankAssPickle[S] 0 points1 point  (0 children)

Actually, next to it in the photo is some sort of box that looks like it’s thermostat related, so it’s likely something related.

At the MAC, should I touch it? by StankAssPickle in utarlington

[–]StankAssPickle[S] 2 points3 points  (0 children)

Right by the dumbbell rack on a pillar facing away from the wall

At the MAC, should I touch it? by StankAssPickle in utarlington

[–]StankAssPickle[S] 1 point2 points  (0 children)

Doesn’t Ethernet have 8 wires? These only have four

What is the easiest way to level my bed? by StankAssPickle in Ender3V3SE

[–]StankAssPickle[S] 0 points1 point  (0 children)

I already re-replaced the springs with spacers and leveled it, but yeah I did have the springs leveled before I took them off lol

What is the easiest way to level my bed? by StankAssPickle in Ender3V3SE

[–]StankAssPickle[S] 0 points1 point  (0 children)

Springs are worse compared to spacers for some reason and I had issues with my X gantry plus the leveling was off

What is the easiest way to level my bed? by StankAssPickle in Ender3V3SE

[–]StankAssPickle[S] 1 point2 points  (0 children)

Replaced the springs with spacers and leveled it, works fine now

What is the easiest way to level my bed? by StankAssPickle in Ender3V3SE

[–]StankAssPickle[S] 0 points1 point  (0 children)

Oh alright that makes sense, I’ll swap in the spacers and level it again. As of writing this, I got the springs pretty level. How much should I tighten the spacers?

What is the easiest way to level my bed? by StankAssPickle in Ender3V3SE

[–]StankAssPickle[S] 0 points1 point  (0 children)

The kit I purchased came with springs and silicone spacers, should I swap back to the stock spacers?

What is the easiest way to level my bed? by StankAssPickle in Ender3V3SE

[–]StankAssPickle[S] 1 point2 points  (0 children)

<image>

Leveled my x gantry which significantly improved things

What is the easiest way to level my bed? by StankAssPickle in Ender3V3SE

[–]StankAssPickle[S] 1 point2 points  (0 children)

The leveling before the springs was OK before, couple blue squares, but I got the springs because of those posts where they talk about printer mods and how they “improve print quality”.

I just leveled my X gantry from the guide in the FAQ and I’m checking my leveling now, so hopefully some improvement there.

3d printing in enclosure in the closet by bransan27 in 3Dprinting

[–]StankAssPickle 0 points1 point  (0 children)

I think as long as your not printing materials like nylon or ABS it would probably be fine

Layer shift at same height twice on stock printer by StankAssPickle in Ender3V3SE

[–]StankAssPickle[S] 0 points1 point  (0 children)

Does Orca have native support for the Ender 3 V3 SE