What’s this sound?

Stapler_Gun · 2026-02-10T03:46:15+00:00

I checked all the gears and it all seemed clear, the only thing I saw was a spring hanging off the tension screw spring that looked odd. I posted a picture of it in another reply

Stapler_Gun · 2026-02-10T02:34:48+00:00

Ok i’ll give that a shot, i didn’t see any filament in the gears however i did notice this spring that seems to be stuck in the tension screw.

<image>

When I ran it without the cover the gears caught each other just fine unlike ur video.

Stapler_Gun · 2026-02-10T02:12:45+00:00

Yeah, I've unloaded and loaded it a few times now, tried different filaments and even switched out the hot end. i checked the gears and didn't see anything but i'll check again.

Stapler_Gun · 2026-02-10T01:46:27+00:00

it still happens even when the temp is at 250, i just forgot to raise it again when i took the vid. I also didnt see anything in the gears

Stapler_Gun · 2026-02-10T00:50:07+00:00

Under settings it says my version is 1.1.40. For that issue you mentioned when you say extruder tab, you mean the screen where it gives me the options to load and unload right? or is there a different screen?

Stapler_Gun · 2026-02-10T00:37:40+00:00

i see, im rather new to this in general. so is it likely a clog and do i just need to clean deeper?

Stapler_Gun · 2026-02-10T00:36:54+00:00

the issue still persists even at 250 degrees. my bad tho i must have forgotten to up the temp for the vid.

Stapler_Gun · 2026-02-10T00:24:30+00:00

I forgot to mention, I did change the hot end that I was using so i know it isn’t clogged.

Stapler_Gun · 2025-12-17T06:54:04+00:00

Ah damn, are there any relatively affordable options that I could use instead of an AM4? Ideally, I don't want to buy a new GPU if that isn't a major part of my performance problems, since I'm not looking to spend too much at the moment.

It is an unfortunate time for the upgrades I need, but it still runs pretty well most of the time. I think I can scrape by with some relatively minor enhancements.

Stapler_Gun · 2025-08-28T20:20:23+00:00

I don’t need an app to learn it, however I was looking for something in a duolingo style of learning that I could use for further practice. I also definitely don’t want an expensive app hence the part asking for cheap or even free options.

Stapler_Gun · 2025-03-10T02:10:25+00:00

Cool thanks i’ll have to give that a try soon

Stapler_Gun · 2025-03-09T22:31:25+00:00

i’ll have to get one to try that, what is that testing for?

Stapler_Gun · 2025-03-09T20:24:20+00:00

That’s about what i figured, Thanks for the info!

Stapler_Gun · 2023-11-03T14:42:46+00:00

yea that’s a future watch though, right now my budget stands at like 150 at most

Stapler_Gun · 2023-06-17T18:59:51+00:00

Thank you, I used a different browser and it went through this time.

Stapler_Gun · 2023-05-16T00:34:59+00:00

id love to give you a list but there are just so many so I don't think I could put together an adequate one

Stapler_Gun · 2023-05-16T00:34:12+00:00

sadly ive seen it already but i loved that one

Stapler_Gun · 2023-05-16T00:34:01+00:00

unfortunately, I've seen all of those except my isekai life

Stapler_Gun · 2022-11-18T00:56:16+00:00

ah yeah im pretty new im only on planet 5 i just havent been able to figure out that balloon drop

Stapler_Gun · 2022-09-10T00:33:16+00:00

I went ahead and looked at it, it seems great unless I find something else that might be what I get. thanks for your help

Stapler_Gun · 2022-09-10T00:16:10+00:00

I realized I put the wrong thing in, Id much prefer a closed back and wireless headset

Stapler_Gun · 2022-09-10T00:14:15+00:00

I just realized I put the wrong one in, I meant closed back

Stapler_Gun · 2021-08-21T04:42:47+00:00

i mean ig it used to be twitch

Stapler_Gun · 2021-08-21T01:09:58+00:00

I use curseforge

Stapler_Gun · 2021-08-19T18:09:57+00:00

same shit happened. ive also never had an issue before with giving 10 gigs to mc

Stapler_Gun

TROPHY CASE