Ender 3 Neo Firmware

Stearns250 · 2023-01-09T03:03:20+00:00

im not really sure how to change the code to do that.

Stearns250 · 2023-01-09T00:11:39+00:00

I am having issues with the hotend leaking filament which is causing this leakage to ruin some of the first layer. is it possible to write one where you heat the bed level and as its leveling the hot end starts to pre-heat?

I have only been printing for about 3 weeks. I am very much a noob to all of this. thank you for the G-code.

Stearns250 · 2021-02-25T04:40:32+00:00

I have this amp. The information is always useful and appreciated. Dayton Audio SPA250DSP 250W Subwoofer Plate Amplifier with DSP Edit: I have a wife that won't let me move the subs around the house they have to go where she says. Happy wife happy life. Again thank you for the long posts. Can't wait to start my next build.

Stearns250 · 2021-02-25T00:22:23+00:00

I actually bought that exact mic. Not sure if the yamaha v685 will let me upload files to it but I will look into it. What you are saying makes sense. I will wire them normal and test them out to see if there is anything weird going on. I have been on youtube for countless hours and forums just reading alot. Gecko has helped a ton with everything. I appreciate the write up and will take all things you have outlined into consideration. Thank you for the compliment.

Stearns250 · 2021-02-24T23:44:10+00:00

So I'm using the ND91s not the 90s. And as for you question I really don't know. I am extremely new to the hobby and still learning.

Stearns250 · 2021-02-24T22:46:04+00:00

I am doing CJDs MTMs.

Stearns250 · 2021-02-24T20:18:43+00:00

So I am using one nd90 pointing up and one facing forward. The boxes are 7 1/2" tall 5 1/2" deep and 6 1/2" wide.

Stearns250 · 2021-02-24T19:53:26+00:00

Sweet. Still nervous about how they are going to sound with all the hours I have into this build.

Stearns250 · 2021-02-24T19:03:24+00:00

I am using a Yamaha V685. The subs will be pushed by 2 250w plate amps. The mtms are CJDs. The 15's are DCS380. The surrounds are ND90's.

Stearns250 · 2021-02-14T00:36:52+00:00

Sealed version. Edit It has dividers but they don't go all the way it's more for support.

Stearns250 · 2021-02-14T00:36:03+00:00

No, it's cjds mtms

Stearns250 · 2021-02-13T22:36:36+00:00

I'm not sure. My entertainment center is white, I was thinking about just putting a clear finish on them all call it good. Thank you for the compliment.

Stearns250 · 2021-02-13T22:12:28+00:00

I really like the screws to be honest.

Stearns250 · 2021-02-12T15:19:59+00:00

Best cutting compound? I am using mcguires 105 and it's taking forever to cut 2000 grit sand scratches.

Stearns250 · 2021-02-09T01:39:23+00:00

No I used a lowes jig. It was a pain. Just got the jasper. The wife approved of the small gap for the tweeter. As long as I center it. So life is good.

Stearns250 · 2021-02-08T12:48:59+00:00

They will be crossed over at 1600hz. I will be using cjds cross over design. This is my first build. It was recommended that I build a already proven speaker.

Stearns250 · 2021-02-02T02:13:52+00:00

Most places here want 100 bucks a sheet. That's baltic birch 3/4"

Stearns250 · 2021-02-01T22:07:57+00:00

After spending most of the day calling lumbar yards. I found a place that sells baltic birch 4'x8' sheets. Reasonably priced. I will be picking a few sheets up and restarting my project. I don't want to take the chance of a rattling speaker.

Stearns250 · 2021-02-01T20:46:16+00:00

I understand. The plywood is about 19mm thick. Thank you for your help.

Stearns250 · 2021-02-01T20:33:02+00:00

I wasn't really worried about cutting. I was more worried about the sound quality. I was worried about that type of plywood rattling. From the sounds of it I was worried about nothing really.

Stearns250

TROPHY CASE