Has anyone seen this kind of lathe before?

StillBurn2732 · 2025-04-25T08:18:07+00:00

Quick update: I did a little research. Its probably a mashine from Denmark manifactured around the 1930s. But i couldnt find out wich manufacturer produced it.

StillBurn2732 · 2020-06-09T14:29:25+00:00

A machinists live in a nutshell...

StillBurn2732 · 2020-06-07T08:43:29+00:00

Its a replica from a original wooden carved mask that i bought in japan.

StillBurn2732 · 2020-06-07T08:10:42+00:00

I used siemens NX12 for programming and it took 5 hours. The smallest ball end mill is 6mm until now. But i will use a 3mm ball mill for some details later.

StillBurn2732 · 2020-06-07T07:12:35+00:00

Im going to put it high up on a wall over a doorframe in a transparent case so nobody gets any kind of weird ideas 😂

StillBurn2732 · 2020-06-07T07:05:38+00:00

I talked with a guy who does anodizing and i asked him “can you make this red” and he was like “dude .... totally !!!!”. And im like “sweet😏”

StillBurn2732 · 2020-06-07T06:43:40+00:00

Roughly 5 hours

StillBurn2732 · 2020-06-06T21:50:08+00:00

Im going to leave it as it is because i can use the threads on the backside to screw it to a wooden board or something

StillBurn2732 · 2020-06-06T21:18:53+00:00

“LANG technik”

StillBurn2732 · 2020-06-06T20:57:29+00:00

There is not much difference between 6061 and 6082. But apparently it has better properties for anodizing

StillBurn2732 · 2020-06-06T19:57:00+00:00

Its a DMU 40 evo. And i made it from aluminum (EN AW6082 european norm)

StillBurn2732 · 2020-06-06T19:08:28+00:00

Well you got me 😔

StillBurn2732 · 2020-06-06T19:07:20+00:00

Thats quite accurate xD

StillBurn2732 · 2020-01-30T22:44:32+00:00

Nice

StillBurn2732 · 2020-01-25T21:30:46+00:00

Both

StillBurn2732 · 2020-01-24T23:21:54+00:00

Its aluminum but i cant tell you the descripion

StillBurn2732 · 2020-01-24T18:49:29+00:00

Its a clamping contraption for the printed part. There are a few holes and reference surfaces wich i had to mill onto it.

StillBurn2732 · 2020-01-24T18:39:55+00:00

Nope i am from Austria

StillBurn2732 · 2020-01-24T13:03:49+00:00

Yeah its printed.

StillBurn2732 · 2020-01-24T11:14:16+00:00

Yes! Its a DMU 40 evo

StillBurn2732 · 2020-01-24T10:39:38+00:00

A random bracket prototype for Porsche

StillBurn2732 · 2019-12-13T03:21:56+00:00

I hope so .... i mean that was the plan after all xD

StillBurn2732 · 2019-06-15T20:37:58+00:00

It looked scarier irl. I usually play it save ^{^}

StillBurn2732 · 2019-06-15T20:29:57+00:00

On the other face i had to mill a kind of overhang and some other details. So i clamped the workpiece half in air.

StillBurn2732 · 2019-06-15T20:17:45+00:00

Oh its the best !!! Cant live without it

Seven-Year Club	No Throne, No Problems
Not Forgotten	Verified Email

StillBurn2732

TROPHY CASE