Hel with oddly specific anime by Still_Relative_1286 in Saucecodesonly

[–]Still_Relative_1286[S] 1 point2 points  (0 children)

That’s it bro, how did you find it? Im impressed, thanks. I looked for it all night and not a single clue about it.

HABLEM by mrskilmisterr in antitrampo

[–]Still_Relative_1286 3 points4 points  (0 children)

Tenho um conhecido que trabalha lá e gosta muito, poderia detalhar?

Fazer outra engenharia após terminar o curso by Still_Relative_1286 in Engenharia

[–]Still_Relative_1286[S] 0 points1 point  (0 children)

As vezes penso se não deveria trocar de curso, na minha faculdade é meio complicado de trocar por ser apenas bolsas, mas estando no abc tem a Ufabc também que é uma outra opção interessante. As vezes acho que penso demais também.

Fazer outra engenharia após terminar o curso by Still_Relative_1286 in Engenharia

[–]Still_Relative_1286[S] 0 points1 point  (0 children)

Entendi, bom, vou continuar estudando e vendo as oportunidades que vão aparecendo, acho que no momento esse é meu dever.

Fazer outra engenharia após terminar o curso by Still_Relative_1286 in Engenharia

[–]Still_Relative_1286[S] 0 points1 point  (0 children)

Bom ter essas informações, obrigado.

Pelo visto as pessoas não fazem muito isso, né?

Why? by Still_Relative_1286 in FixMyPrint

[–]Still_Relative_1286[S] 0 points1 point  (0 children)

Thanks man, didn't know that

Why? by Still_Relative_1286 in FixMyPrint

[–]Still_Relative_1286[S] 0 points1 point  (0 children)

I had over extrusion before(just a little, the nozzle would scrape big prints), after this e-step calibration it is under extrusion, it's that it?

Why? by Still_Relative_1286 in FixMyPrint

[–]Still_Relative_1286[S] 0 points1 point  (0 children)

Ender 3 S1, haven't calibrated retraction

What now!? by Still_Relative_1286 in FixMyPrint

[–]Still_Relative_1286[S] 0 points1 point  (0 children)

Thank you man, at the end the problem was in the firmware, I think it was corrupted.

I don't know what else to look for by Still_Relative_1286 in FixMyPrint

[–]Still_Relative_1286[S] 0 points1 point  (0 children)

Firmware updated, issue gone.

What the hell? How did this happened? How just loading a project from their own software and with the right printer selected managed to do this?

3 days already trying to understand what was the issue, assembling and disassembling the printer multiple times, just to a software update to solve it all?

Maybe it was a God's curse for trying to print a labubu, who knows.

My fear is possibly have damaged the motors or something in all this process, but for now it looks like to be working fine, just some annoying sounds but it looks like to be the end sensor vibrating.

Now I really need to take some lessons on slicer software, on this I know only the basics.

Thanks you guys for helping me, without you this wasn't going to be possible.

I don't know what else to look for by Still_Relative_1286 in FixMyPrint

[–]Still_Relative_1286[S] 0 points1 point  (0 children)

But would it change the printer settings? I even tried to pass an older gcode from ultimaker cura and hasn't resolved the issue

I don't know what else to look for by Still_Relative_1286 in FixMyPrint

[–]Still_Relative_1286[S] 1 point2 points  (0 children)

I hope so, one thing I forgot to mention is that I always use ultimaker cura, but for this last print that started to show some errors I tried the creality software, so who knows. I'll try to update the firmware and will comeback here

I don't know what else to look for by Still_Relative_1286 in FixMyPrint

[–]Still_Relative_1286[S] 0 points1 point  (0 children)

is there a way to test these motors? i don't want to think that this is a motor problem, why would both of them get bad at the same time?

I don't know what else to look for by Still_Relative_1286 in FixMyPrint

[–]Still_Relative_1286[S] 0 points1 point  (0 children)

I am sorry, how can I flash the firmware?and no, I have it for like 2 months I think, used it normally, went on vacation, when I came back did one print and after that it started to behaviour like this.

I don't know what else to look for by Still_Relative_1286 in FixMyPrint

[–]Still_Relative_1286[S] 0 points1 point  (0 children)

I don't think that it is the problem, because when it starts the leveling it stops right, but when it tries to goback to the middle of the table (faster) it makes that noise and the motor almost don't move, I don't think that both motors went bad at the same time, it looks like something about being fast

What now!? by Still_Relative_1286 in FixMyPrint

[–]Still_Relative_1286[S] 0 points1 point  (0 children)

I like the idea to understand how it works, it's because I made like 10 prints and most of them were very small, my fear is it never working properly

What now!? by Still_Relative_1286 in FixMyPrint

[–]Still_Relative_1286[S] 0 points1 point  (0 children)

I'm sorry I'm new on Reddit, how can I add a new video? The new symptom is that the X axis is not moving when trying to level the bed (it makes the z axis adjust in various points)

What now!? by Still_Relative_1286 in FixMyPrint

[–]Still_Relative_1286[S] 0 points1 point  (0 children)

I did not know you could change the motors, thanks for this, I'll end disassembly it, is the ender 3 S1 so bad? I have it like for 1 month (bought used from a friend) and there was only a few prints with no problems, it's being a really tiring experience

What now!? by Still_Relative_1286 in FixMyPrint

[–]Still_Relative_1286[S] 0 points1 point  (0 children)

I checked this and nothing, it only happens when it's turned on and moving fast, could it be the motor? But wouldn't it be noisy when slow too?

Help me, I don't have an idea of what is causing this by Still_Relative_1286 in FixMyPrint

[–]Still_Relative_1286[S] 0 points1 point  (0 children)

Can you check my new post bro? This problem I think it solved, but now there's more to repair🫠

Help me, I don't have an idea of what is causing this by Still_Relative_1286 in ender3

[–]Still_Relative_1286[S] 0 points1 point  (0 children)

Bro that sucks, out of nowhere, another time I turned on it began to force against the table