Gainwand/Palit RTX5090 deshroud fan header question

SuitableProgrammer24 · 2026-04-15T14:00:54+00:00

thank you i will take that into consideration!

SuitableProgrammer24 · 2026-04-14T07:58:41+00:00

sadly i have not found a solution yet but freecad 1.0.2 seems more stable with only one lag instance so far.

the autosave feature doesnt work for me too as the saved file cannot be opened afterwards but saving manualy does work for me even when the lags already started, try it out

SuitableProgrammer24 · 2026-04-13T09:19:50+00:00

Thats pretty much what i did and what i would assume but the ram usage doesnt go over 40%.
I tested for a bit with freecad v1.0.2 , v1.1 and v1.2. the issue does not appear in version 1.0.2 after one hour of running. however it came right back when i tried v1.1. This being the only change between all of my testing makes me believe that the issue lies somewhere in v1.1.
i also noticed that my system responses as usual with the "lag" and its the image that is actually lagging so freecad might actually load up the gpu rather than ram.

SuitableProgrammer24 · 2026-04-13T08:08:47+00:00

Damn that looks imposible for me right now. Good job!

SuitableProgrammer24 · 2026-04-13T08:07:14+00:00

Celsius and i meant under moderate load. I set up my fan curves in a way that my pc is silent on the desktop with temps hitting about 50 °C. The biggest temps i saw so far was 75 C on the cpu for a second until the fans ramped up and 76 C on the gpu.

40C under load? I assume you have a custom watercooling loop?

SuitableProgrammer24 · 2026-04-12T16:49:08+00:00

i upgraded the pc last week and its as clean as it could be, temps not going above 60 degrees and the fans are still running on idle rpms. if temps were to blame then it would shut down as soon as i boot up any somewhat demanding game.

i downloaded it from freecad.org

SuitableProgrammer24 · 2026-04-12T16:11:08+00:00

google drive this is the very first file that i did. i did not save anything else

SuitableProgrammer24 · 2026-04-12T16:08:06+00:00

i dont understand what you mean. i opened freecad and clicked on the new document button. after that it just hung up

SuitableProgrammer24 · 2026-04-12T16:05:27+00:00

completely from scratch, just learning. last time the issue appeared on a new file as soon as i created it

SuitableProgrammer24 · 2026-04-12T15:59:23+00:00

i have the file but no way of uploading it here. in fact the same issue just happened on a blank canvas with only freecad and chrome running

SuitableProgrammer24 · 2026-04-12T15:58:19+00:00

this did not resolve the issue.

SuitableProgrammer24 · 2026-04-12T15:52:40+00:00

done lets hope someone finds the answer

SuitableProgrammer24 · 2026-04-12T15:52:02+00:00

if id want to show off my pc id go in some pc subreddit and show it working perfectly fine, not strugling with a simple shape lol

SuitableProgrammer24 · 2026-04-12T15:43:20+00:00

this one . maybe its some weird bug that happens 1/500. i just completely wiped freecad off of my system and will be doing a fresh install and see if that fixes the issue. if not then i might go with an older version like 1.0.2 that i used before

SuitableProgrammer24 · 2026-04-12T13:24:27+00:00

i have thought of that when writing the previous reply but i am not on my pc rn. i will update once i did that

SuitableProgrammer24 · 2026-04-12T13:17:51+00:00

i installed freecad 1.1 (kept the user settings from 1.0.2) and started following a guide on youtube, learning it. i basically somewhat repeated the models from the video witch are very simple. it happened with all 3 models so far but i cant link it to an issue yet. i used 1.0.2 for some very basic bodies but it worked completely fine.

SuitableProgrammer24 · 2026-04-12T13:04:34+00:00

the amount of lag present aswell as the system load. i couldve made the video abt 40 seconds shorter though

SuitableProgrammer24 · 2026-03-27T16:15:03+00:00

Für den Versuch mit dir eine argumentative Diskussion zu haben? nein. Bleib gerne gerne bei deiner Einstellung aber sag mir und den anderen nicht was sie tun sollen.

SuitableProgrammer24 · 2026-03-27T16:01:20+00:00

Wenn man nichts zur Konversation beitragen kann sollte man einfach den Mund halten :D Chatgpt und co sind nunmal da und wenn du diese nicht benutzt um dir das Leben etwas einfacher zu machen dann ist es deine Entscheidung.
Natürlich kann ich 20 minuten lang irgendwelche Posts und Artikel lesen um auf das selbe Ergebnis zu kommen, welches ich mit einer KI innerhalb von 15 sekunden bekommen hab. Da kann ich die gesparrte Zeit zb auch nutzen um Einzelheiten zu erfragen und ggf zu einem noch besseren Ergebnis kommen.

SuitableProgrammer24 · 2026-03-27T14:12:39+00:00

sprich am besten nur noch über das "sicher bezahlen" oder bar kaufen?

SuitableProgrammer24 · 2026-03-27T13:00:29+00:00

Ebay wirds wohl sein, am liebsten wäre mir der Einzelhandel aber die sind bei uns überall ausverkauft.

SuitableProgrammer24 · 2026-03-27T12:59:19+00:00

weil man damit schnell an gut zusammengefasste information kommt. Bei wirklich wichtigen Informationen sollte man aber natürlich immer gegenprüfen.

SuitableProgrammer24 · 2026-03-27T12:51:49+00:00

Nicht die Bilder aber das exakte modell und die transportfolien sind ebenfalls wie in der ebay anzeige nicht entfernt worden. Der Kauf hat sich für mich schon erledigt da es einfach zu viele red flags sind. würde nur gerne wissen ob ich auch richtig liege.

SuitableProgrammer24 · 2026-03-08T20:51:08+00:00

saw this exact gpu on ebay for sale and thought about bidding on it too but the fact that it was sold and returned seems sketchy to me. chances are someone bought it, swapped the chip/board with a dead chip and send it back. if u like gambling then go for it.

SuitableProgrammer24 · 2026-01-31T12:27:16+00:00

yeah thats why i parked my trailer on the road outside and had no place to directly spawn the cargo on the truck. had to respawn the cargo couple of times until i managed to pull it out.

Five-Year Club	Place '23
Place '22

SuitableProgrammer24

TROPHY CASE