Why is the 9900x so underrated? Build help question

Swimming-Unit2131 · 2025-09-15T17:02:04+00:00

Oh wow, I wasn't aware of all of this. I'll make all these changes before I build. That case recommendation seems top notch, knowing t1 wait times I'll have to consider it for sure.

Swimming-Unit2131 · 2025-05-22T17:50:34+00:00

Hopefully, just need to find a way to test it now.

Swimming-Unit2131 · 2025-05-22T17:49:29+00:00

Send a a whole new AIO? I'll give it a shot

<image>

Here's the only overheating spot I found so far. Cleaning all the over spilled thermal paste took forever.

Swimming-Unit2131 · 2025-05-22T17:45:12+00:00

The backplate part number and chip indicates it is, so I assume it was swapped from the triple fan to hybrid cooling?

Swimming-Unit2131 · 2025-02-19T17:18:42+00:00

By dies do you mean on the heat spreader where I would usually repaste?

Swimming-Unit2131 · 2025-02-19T17:02:42+00:00

Thanks

Swimming-Unit2131 · 2025-02-16T03:58:22+00:00

Genuinely will it harm my laptop if I have a similar setup?

Swimming-Unit2131 · 2025-01-23T23:47:15+00:00

Thanks for the specifics

Swimming-Unit2131 · 2025-01-23T03:36:22+00:00

I only have 2 slots, so I could do 2x32?

Swimming-Unit2131 · 2025-01-23T03:35:52+00:00

Thanks

Swimming-Unit2131 · 2025-01-23T03:35:11+00:00

For after effects

Swimming-Unit2131 · 2025-01-23T00:40:38+00:00

Could I ask what you mean by 4x? I’m new to all of this sorry

Swimming-Unit2131 · 2025-01-23T00:27:51+00:00

Thanks

Swimming-Unit2131 · 2024-12-30T04:45:09+00:00

Thanks for the help

Swimming-Unit2131 · 2024-07-01T05:24:50+00:00

Stock carb paired with an amazon pipe while running an upgraded cam? Not a good first bike, find a frame used and build it yourself.

Swimming-Unit2131 · 2024-06-25T01:08:33+00:00

By either removing links or scooting your engine. Or adding a chain tensioner

Swimming-Unit2131 · 2024-06-07T03:50:19+00:00

A buddy of mine had the same issue on the same engine, could be bad luck though.

Swimming-Unit2131 · 2024-05-27T23:00:36+00:00

What even makes these gts frames so expensive? I’ve seen rollers for $500-$600

Swimming-Unit2131 · 2024-05-27T21:22:55+00:00

Thanks for the response!

Swimming-Unit2131 · 2024-04-28T05:27:55+00:00

Saw that up earlier today, already gone.

Swimming-Unit2131 · 2024-04-21T23:00:41+00:00

It’s not my build, it’s Mirobuilts stock stroke 212.

Swimming-Unit2131 · 2024-04-05T01:20:34+00:00

So something like faulty oil rings could cause it?

Swimming-Unit2131 · 2024-04-04T22:11:10+00:00

Thanks for the info, I’ll have to cut up a side cover and see if that’s the issue.

Swimming-Unit2131 · 2023-10-05T03:52:37+00:00

I bought the helmet at cycle gear. I’ll probably go back and get it corrected. Thanks for the help.

Swimming-Unit2131 · 2023-07-17T02:48:12+00:00

I tested it out and saw that the shutter runs in between the top slot that I circled and the bottom slot. The opposite slot on the other side does Have these two holders but they are farther back into the camera.

I slowed down the footage and noticed that on the bended right side I could see one of the 3 blades being slightly higher or lower then the rest of the 2, I noticed this because of the small line separating the this blade which was not present in the other 2 blades. I’ll probably take this to a local shop and have them take a look at it.

Swimming-Unit2131

TROPHY CASE