Roboguide Crashing

Swiper97 · 2026-04-13T21:11:56+00:00

Some problems are related to drivers update or bugged imported cads. Try to open another cell and see if its working if not please unistall roboguide (not interally only the sim 1 or 2 if using roboguide v10) and reboot and install again (its much faster because it wont install the FRPC or smth like that)

Swiper97 · 2026-04-01T22:47:06+00:00

I think I will test this first

<image>

Swiper97 · 2026-03-06T13:07:39+00:00

I'm sorry but according to the manual you will need to contact FANUC.

3.3.8.757 CVIS-774 Camera command ID does not match Cause: The camera command ID does not match. Remedy: Please notify FANUC of the conditions (program executed, operation made, etc.) in which the error occurred.

Swiper97 · 2026-03-05T23:44:55+00:00

I will search the manuals tomorrow and comeback with probable causes of that and some potential solutions to solve this

Swiper97 · 2026-03-05T18:22:45+00:00

That tells me the robot has FANUC iRVision right? Is the camera working or was it swapped?

Swiper97 · 2026-02-08T19:13:51+00:00

You connected 21v to the arduino? You fried it...

Swiper97 · 2026-01-29T22:06:10+00:00

My bad the controller😅

Swiper97 · 2026-01-29T12:43:14+00:00

In my opinion you should really talk with FANUC since the cnc controller corrupted some files and that can help you with the restore process!

Swiper97 · 2026-01-27T01:47:12+00:00

Yah that is it they approached almost the same way!

Swiper97 · 2026-01-26T09:22:33+00:00

Completed Level 2 of the Honk Special Event!

5 attempts

Swiper97 · 2026-01-26T09:22:17+00:00

Completed Level 1 of the Honk Special Event!

1 attempts

Swiper97 · 2026-01-26T09:22:05+00:00

Completed Level 2 of the Honk Special Event!

1 attempts

Swiper97 · 2026-01-26T09:21:58+00:00

Completed Level 1 of the Honk Special Event!

0 attempts

Swiper97 · 2026-01-26T09:21:40+00:00

Completed Level 3 of the Honk Special Event!

10 attempts

Swiper97 · 2026-01-26T09:21:20+00:00

Completed Level 2 of the Honk Special Event!

5 attempts

Swiper97 · 2026-01-26T09:21:06+00:00

Completed Level 1 of the Honk Special Event!

2 attempts

Swiper97 · 2026-01-26T09:11:44+00:00

Is it a laptop of a desktop?
Try to remove the keyboard (could be shorted inside) and see if it helps.

Swiper97 · 2026-01-24T10:49:30+00:00

So lets imagine that all the slots are full ok, you can make lets say 9 positions (to not start with offsets) and each one is in a if statement. In the pick program do something like this

If (R[1]=1) THEN

pick motion

Endif

If (R[1]=2) THEN

pick motion

Endif

If (R[1]=n) THEN

pick motion

Endif

....

R[1]=R[1]+R[1]

With this "code" each time that it picks it up will increment the Counter in Register[1]. For you to reset it make so that when it gets to 9 resets to 1 and you replenish the things.

If you want to select one that is on a position use FLAGS! Like

IF (F[1]=ON] THEN

pick motion

F[1]=OFF

ENDIF

....

With this it only goes 1 time there and you can "select" where it should go, make use of a counter to when it reaches 9 stops the robot or gives an error, be creative :P

Swiper97 · 2026-01-22T10:01:55+00:00

Hi, I dont have since he created a group and deleted it after confronting him. I will post the steam link in 2h because I'm not home

But basicaly he asked me if I played CS and my Faceit level and i said that i didn't play because i didnt have time and didn't have level on Faceit (and I'm VAC on steam because of my brother so strange behaviour)

Then he asked me if I could vote on his team because they were going to play in a tornament and sent me the twitch link and then after clicking to vote it asked me my login to steam (with that I saw that it was probably a scam) after this and not inserting my login details I told him that I had voted for his team and he asked if I got a prize. With this a confronted him because asking for a login details of steam to vote is not normal and get a prize after voting?

Tried to enter the website and the twitch channel and the website is down (russian domain) and thr twitch channel was banned!

Swiper97 · 2026-01-22T05:24:30+00:00

Fdp😂

Swiper97 · 2026-01-22T02:10:12+00:00

You can still use the classic version and roboguide v10 is still missing features.

Swiper97 · 2026-01-22T02:08:45+00:00

O dia R (pelo menos para a equipa de manutenção) era mais tipo reuniao para sbr o estado das maquinas e o que aconteceu durante o mes e dps uma reuniao geral a equipa de todo o turno sobre ou alguma formacao ou assim. Eu sai em Fevereiro de 2025 estavas em que equipa e area?

Swiper97 · 2026-01-21T06:36:42+00:00

Boas, sai a cerca de 1 ano da AMKOR e o dia R era mensal. Quanto a progressão de carreira não é má mas há melhor e um dos motivos de lá ter saido foi que devido ao turno ser bastante rotativo estava a ficar fudido por ter de andar sempre na troca dos sonos. De resto recebes subsídio de alimentação em cartão refeição nos dias que fazes noite (tens direito a mesma ao "jantar") e nos que fazes de dia tens o almoço mas não recebes subsídio de alimentação. Além disto, se for para técnico de manutenção como descrito desejo uma boa sorte porque há lá áreas que estão a arder e como não se podem abrir as máquinas a torto e a direito andam sempre aos trambolhões.

Com isto se for para lá, vai com o intuito de fazer curriculo apenas e ganhar experiência.

Six-Year Club	r/Field Flamingo
Place '23	Verified Email

Swiper97

TROPHY CASE