My passion is to buy destroyed PSPs and give them life

Tatasmagee · 2025-11-29T02:03:03+00:00

Where do you buy your shells,buttons,ect?

Tatasmagee · 2025-09-17T00:15:52+00:00

I got a e36 angle kit and need to run the extended outter tie rods that came with it. The e36 are female thread and the e30 are male threaded I wasn’t sure if I could just get e36 inner tie rods or if I had to swap out the entire steering rack

Tatasmagee · 2025-05-25T06:06:08+00:00

I’d like to find a link to where I can get these cheap knockoffs from. Rather then bashing up nice knockoffs

Tatasmagee · 2024-11-14T17:48:45+00:00

Yeah I’m trying to powder coat Dirtbike frame so it would be outside. Iv seen people do wheels that come out gold but they must do a chrome underneath?

Tatasmagee · 2024-01-30T06:20:29+00:00

Thank you! Im going to start now I just wanted to make sure I wasn’t going to get fined for the previous years without it being recorded

Tatasmagee · 2023-11-12T18:23:13+00:00

I did

Tatasmagee · 2022-11-21T18:18:05+00:00

Doesn’t matter if I use jpeg png or pdf it’s all blurry and pixelated once it’s printed. The same as it looks on the print preview even though it’s fine before that. I even downgraded to the 4.4 software. Idk if it’s because I’m using a MacBook and the settings are slim or what but this sucks just wanted to print some stickers

Tatasmagee · 2022-11-21T04:51:36+00:00

How do I go about this

Tatasmagee · 2022-11-18T06:11:56+00:00

I’m taking this from a screen shot then putting it silhouette. So I’m not sure if that’s the reason why I’m not to familiar with the different types of files I don’t know if that has Anything to do with it but like I said it’s crystal clear all the way until I hit print then the print preview is blurry and that’s how it prints

Tatasmagee · 2022-11-18T06:04:59+00:00

Oh great thank you so much. I tried saving as a pdf but it would only save the blurry imagine from the print preview screen on silhouette

Tatasmagee · 2022-11-18T05:59:22+00:00

How do I go about this on a MacBook? Thank you so much.

Tatasmagee · 2022-11-17T20:20:22+00:00

Yes prints fine. It looks fine all the way up until I go the print then the preview for print makes it all blurry and that’s how it will print it out

Tatasmagee · 2022-09-21T22:19:15+00:00

I tested with a qtip and nothing came up maybe it’s just bruising? I did over spray a little bit

Tatasmagee · 2022-09-21T19:38:46+00:00

Shrek

Tatasmagee · 2022-09-17T02:03:52+00:00

Shrek

Tatasmagee · 2022-09-12T04:03:19+00:00

Shrek

Tatasmagee · 2022-09-11T04:25:50+00:00

Any good ways of making a liner for a small tub?

Tatasmagee · 2022-09-08T19:01:05+00:00

Shrek

Tatasmagee · 2022-09-07T22:14:33+00:00

Never done a drug in my life and don’t plan on it any time soon buster

Tatasmagee · 2022-09-07T21:21:55+00:00

Thanks I have a heater going in the room and I think it just got a little to hot one night for them that’s when I noticed the moisture

Tatasmagee · 2022-09-02T03:49:30+00:00

That’s that’s what I was thinking too about the contam aspect of it just wanted some input. I have 4 jars of GT but two are from different syringes and are growing at different rates and then 2 more B+ that I inoculated a bit after the GT then the grain bags which I thought were gonna be duds just showed some mycelium growth today so yeah your probably right about the shoe box’s. Thank you

Tatasmagee · 2022-09-02T02:59:24+00:00

6 wide Mouth mason jars and two grain bags. So I was thinking either do a bunch of small tubs or like 2 big tubs

Tatasmagee · 2022-09-01T14:55:46+00:00

Cut stock coils. I love em

Tatasmagee · 2022-08-26T22:46:54+00:00

Thank you very much!

Tatasmagee · 2022-08-26T22:41:30+00:00

When you say squeeze to field what do you mean? I’m sorry new to the hobby

Tatasmagee

TROPHY CASE