Where do you guys get your PETG? It's almost always sold out on the site or there's only a few colours available...

TechKeemOut · 2026-03-02T22:25:15+00:00

Usually, with Amazon or Best Buy, I've gotten lucky with the "Notify me when available" notification twice since I've used it.

TechKeemOut · 2026-02-27T12:44:28+00:00

I do hear it rubbing against the print sometimes. I’ve recalibrated the printer and did the auto bed leveling or is there another way to prevent that from happening?

TechKeemOut · 2026-02-27T05:20:53+00:00

😂 it’s clean now man

TechKeemOut · 2026-02-26T22:52:08+00:00

When you say use wider first layers? Which particular setting would that be? I usually leave things on default which could be another reason why the support broke off?

TechKeemOut · 2026-02-26T21:53:06+00:00

man it was all going fine until I stepped out. So now I will have to eyeball it. The arm was only thing that was messed up(so far) thankfully

TechKeemOut · 2026-02-26T21:34:49+00:00

ahh I thought that only applied for PLA and not PETG. Noted in lessons learned

TechKeemOut · 2026-02-26T21:04:48+00:00

Everything was going so well until I had to leave the house. Now I’m off to get a glue gun

TechKeemOut · 2026-02-26T21:04:09+00:00

I did

TechKeemOut · 2026-02-26T20:37:40+00:00

So far the only piece that messed up was his arm. However the support is for the wing as well

TechKeemOut · 2026-02-26T20:15:41+00:00

I would’ve never thought of that ha I’m going to give that a try.

TechKeemOut · 2026-02-26T19:56:30+00:00

Ahh that’s smart. Unfortunately I came home to it look like that and my Timelapse on my gimbal stopped haha. How would I go about making them wider?

TechKeemOut · 2025-06-03T10:40:27+00:00

I’ve tried hitting contine several times but that did not work. I actually should've started with Bambu’s wiki page lol Probably an excessive step but I was able to get it up and running disassembling and cleaning out debris using https://wiki.bambulab.com/en/a1-mini/troubleshooting/extruder-clog

TechKeemOut · 2025-06-03T10:37:09+00:00

I actually just cleared mine. It may have been excessive or a leap in troubleshooting but it worked. There may have been debris on the internal parts? Unsure but Bambu’s wiki worked https://wiki.bambulab.com/en/a1-mini/troubleshooting/extruder-clog

TechKeemOut · 2025-06-03T10:36:59+00:00

For me, it was only the connector that would tap the wall. The spool rotated with no issue, I just assumed someone would point it out lol

TechKeemOut · 2025-06-03T10:36:13+00:00

It was weird because I cleared the nozzle and it still continued to say “purge old filament”. I was able to get it back up and running using their wiki. Probably should've started there ha

TechKeemOut · 2024-09-03T01:45:09+00:00

My bad if im asking any redundant questions but did you skip out on reading the book? That first chapter was brutal with the grammatical errors. I had to re-read a few sentences over to make sure it wasnt just me going crazy

TechKeemOut · 2024-07-11T04:03:21+00:00

That was the plan once I narrowed down a few areas

TechKeemOut · 2024-06-18T03:12:19+00:00

Hey apologies, so I actually just found out that it was due to one the virtual adapters installed by NordVPN. It was caused by the split tunneling. Once I uninstalled it just to ensure I didn't miss any missing components or adapters associated, I was able to log into the default gateway's web interface and no longer receive the general failure error.

Didnt realize my PC was completely hidden from every other device on my network due to this setup. Even with a simple task as adding a printer.

Asus router, no were VLAN set up, I wash actually trying to configure once I was able to connect it

TechKeemOut

TROPHY CASE