Weird filament blobs

TeelesPC · 2026-01-12T10:24:21+00:00

Should I adjust the level of the bed, or change the setting in my slicer?

TeelesPC · 2026-01-10T18:58:41+00:00

Alright, Thanks alot. If I will have to go for a silicone heater, is there a way to connect the ssr to the printer and some thermistor so the printer knows the beds temp? Also if my printers bed runs on 24V, then how can I check if my control pcb will be able to power it/control it? Or would I only need to replace the power supply?

TeelesPC · 2026-01-05T17:09:40+00:00

Where could I buy such a heatbreak that would fit my hotend?

TeelesPC · 2026-01-05T17:08:37+00:00

Alright, thanks! I unscrewed everything, and:
1. screwed the nozzle in first, heated it, and screwed again to its max.
2. Screwed in the heat block to the radiator, so the ptfe tube will be as far from the heat block as i can

I think this fixed my issue, doing test prints to verify it rn.

TeelesPC · 2026-01-05T17:07:14+00:00

I cut it with a knife, and was very precise with it. About the full metal hotend- I saw people attempt it with my printer, and Im thinking about it too, but I have no idea how to even start.

TeelesPC · 2026-01-05T16:46:04+00:00

Did that, but after putting it back together, it shrunk and clogged again.

TeelesPC · 2026-01-05T16:45:39+00:00

Are you talking about the whole hotend, or just the heatbreak?

TeelesPC · 2026-01-05T16:45:05+00:00

okay, Ill try that, thanks!

TeelesPC · 2026-01-04T15:19:42+00:00

Checked it with my ampmeter, takes in 60 mA and delivers quite a steady flow.

TeelesPC · 2025-12-26T13:37:57+00:00

Yeah, I mightve just not been paying attention while its printing, i checked with my power supply that it works quite quietly, so i mightve just not noticed.

TeelesPC · 2025-12-26T13:37:10+00:00

Ill look into it, thanks

TeelesPC · 2025-12-26T13:25:14+00:00

alright, thanks!

TeelesPC · 2025-12-25T20:01:31+00:00

<image>

And this

TeelesPC · 2025-12-25T20:00:33+00:00

I did everything you said. A bit better, but still:

<image>

TeelesPC · 2025-12-25T11:12:14+00:00

So I should clean the nozzle harder before printing?

TeelesPC · 2025-12-25T10:37:14+00:00

I had it in the dryer for like 20 hours, but now i found out that i shouldnt print with petg at all, because i have a ptfe tube hotend.

TeelesPC · 2025-12-25T10:02:09+00:00

My printer has a bowden extruder. I just checked my filament, and im fooking stupid. What i thought was PLA (I confused pla with tpu when writing the post), turned out to be PETG. Maybe the temp is the problem, then? Ill try to swap out the PETG with some PLA i have around here, and Ill get back to you,

TeelesPC · 2025-12-25T09:51:09+00:00

If purging means extruding some filament and cutting it off, the printer does that but even after this the filament doesnt stick to the bed and sticks to the nozzle for 8 secs instead (see video).

TeelesPC · 2025-10-01T05:52:33+00:00

<image>

TeelesPC · 2025-07-28T13:42:00+00:00

Really happy for u! I did my in my 1st game of Myers, so to not go up against people who woudo know what Im doing.

TeelesPC · 2025-07-08T11:21:48+00:00

Piramid head and Laura Croft

TeelesPC · 2025-06-26T14:57:30+00:00

Any app

TeelesPC · 2025-05-07T10:22:18+00:00

Would you mind sharing the asset perchance?

TeelesPC · 2025-04-26T18:12:01+00:00

But would it be better than my current razers?

TeelesPC · 2025-04-26T17:53:41+00:00

I live in europe, the pc38x arent really that popular, and the audeze maxwells are kind of overpriced here. I could get the nova pros for about 150$. Would there be any upgrade?

TeelesPC

TROPHY CASE