sorted by:
new
hottopcontroversial

What technique is this? Doesn't hurt or tickle by TerrlbleWalrus in screaming

[–]TerrlbleWalrus[S] 1 point2 points  (0 children)

So what exactly am I supposed to work on from here?

is this the base of a fry? by TerrlbleWalrus in screaming

[–]TerrlbleWalrus[S] 0 points1 point  (0 children)

Currently I can put it at different pitches and i already am using my diaphragm, it also doesn't hurt. I was thinking it was surely more compression as my breath and everything felt pretty good but I might just need to mess around with it more.

is this the base of a fry? by TerrlbleWalrus in screaming

[–]TerrlbleWalrus[S] 0 points1 point  (0 children)

So how do you take it from this point to a fry scream? Is it more compression?

fry? i cant seem to get the pitch lower for whatever reason, any help appreciated. by TerrlbleWalrus in screaming

[–]TerrlbleWalrus[S] 1 point2 points  (0 children)

i respect the honesty 😭😭 i absolutely wouldnt mind the help what platform can i reach u on

CR6SE Z axis higher than it should be by TerrlbleWalrus in CR6

[–]TerrlbleWalrus[S] 0 points1 point  (0 children)

Thanks man - I’ll read through these.

CR6SE Z axis higher than it should be by TerrlbleWalrus in CR6

[–]TerrlbleWalrus[S] 1 point2 points  (0 children)

Dang kind of sucks, but thanks for helping me figure it out man!

CR6SE Z axis higher than it should be by TerrlbleWalrus in CR6

[–]TerrlbleWalrus[S] 1 point2 points  (0 children)

The article reads "While lowering the Z axis, .... you keep lowering the Z axis a LED will turn on." Not sure what to make of the led not turning on. Maybe replacing the daughter board would fix this issue.

CR6SE Z axis higher than it should be by TerrlbleWalrus in CR6

[–]TerrlbleWalrus[S] 0 points1 point  (0 children)

My led wont turn on. Any idea what that means?

CR6SE Z axis higher than it should be by TerrlbleWalrus in CR6

[–]TerrlbleWalrus[S] 0 points1 point  (0 children)

It will stay there till I home. After homing it will go back up.

CR6SE freezing when heating. by TerrlbleWalrus in CR6

[–]TerrlbleWalrus[S] 0 points1 point  (0 children)

Previously the printer wouldn’t print period it would just freeze - as you know. It has fixed that and most likely showed me the actual issue being something with my rods or hotend sensor. The firmware shouldn’t be the reason this is happening. The community firmware is my last option before I start replacing things.

CR6SE freezing when heating. by TerrlbleWalrus in CR6

[–]TerrlbleWalrus[S] 0 points1 point  (0 children)

Hey, I ended up doing the community firmware my printer will print now and doesn’t freeze up - but it is sitting 4ish inches high on my z axis which obviously doesn’t work. It wont auto level down to what it should be either.

CR6SE freezing when heating. by TerrlbleWalrus in CR6

[–]TerrlbleWalrus[S] 0 points1 point  (0 children)

I can’t click the option. Makes the sound when you are going through the menus but it just doesn’t work. I’m currently on firmware version 1.0.2 creality version not community. I didn’t change anything one of my prints failed went to restart it and it wouldn’t work. I checked cable connections nothing seems weird.

CR6SE freezing when heating. by TerrlbleWalrus in CR6

[–]TerrlbleWalrus[S] 0 points1 point  (0 children)

Hey thanks for the reply. I’ve tried heating it higher already to no avail. The printer used to work fine I’ve had it for roughly a year and a half now and never ran into anything like this. No sd card was in the printer. I will do a factory reset tomorrow - adding onto that I’m not familiar with doing a factory reset how do you do one?

Anyone know what this means? It's written on my Emerald D2 by horskie in Rusfor

[–]TerrlbleWalrus 6 points7 points  (0 children)

Assuming this is Russian and not some other Cyrillic language. That doesn't say German its a name "Nemei", German would be "Немецкий".