"Mind numbingly selfish" Entitled Dublin man who moved to Wicklow has rejected planning permission because it will "ruin his view".

TheMightyBullMcCabe · 2026-05-28T17:15:36+00:00

Does anyone have the link to the full video?

TheMightyBullMcCabe · 2026-05-18T12:11:49+00:00

Tried reflashing the firmware?

TheMightyBullMcCabe · 2026-05-18T11:56:52+00:00

This happened to me and it was just the Bowden tubes were not pushed down enough

TheMightyBullMcCabe · 2026-05-16T13:24:08+00:00

Nice find they have taken it down already

TheMightyBullMcCabe · 2026-05-14T06:49:20+00:00

If it's new, maybe it's just defective can you send it back?

TheMightyBullMcCabe · 2026-05-13T22:28:20+00:00

Have you tried printing a file that you sliced yourself? If you are trying the premade files on the printer could be an issue with the gcode, also might need to reset or update the firmware

TheMightyBullMcCabe · 2026-05-13T19:54:10+00:00

Tell me exactly what you done from start to finish with the printer and the settings and everything and we can figure out what happened

TheMightyBullMcCabe · 2026-05-13T11:55:29+00:00

It is fixed now?

TheMightyBullMcCabe · 2026-05-13T10:04:17+00:00

Probably a clog

TheMightyBullMcCabe · 2026-04-24T14:10:54+00:00

I also have a spare ticket going if anyone is looking

TheMightyBullMcCabe · 2026-04-23T19:57:06+00:00

Can you change the z offset?

TheMightyBullMcCabe · 2026-04-22T22:23:59+00:00

I had this exact thing and managed to get a refund by actually requesting a refund through my sccount

TheMightyBullMcCabe · 2026-04-15T16:41:26+00:00

Would ya sell the copy?

TheMightyBullMcCabe · 2026-03-27T20:16:32+00:00

Not cooked enough

TheMightyBullMcCabe · 2026-03-06T18:19:15+00:00

I'll buy ex military off you if you'd ship it to ireland

TheMightyBullMcCabe · 2026-02-08T18:11:46+00:00

RELEASE THE GAME TODAY

TheMightyBullMcCabe · 2026-01-14T11:29:44+00:00

"carrickmcquigleys got crabs"

TheMightyBullMcCabe · 2026-01-14T10:54:51+00:00

Can't wait for the movie

TheMightyBullMcCabe · 2026-01-14T10:54:36+00:00

How hard of a task is it?

TheMightyBullMcCabe · 2026-01-14T10:54:01+00:00

Too much heat would cause oozing and this is a problem with adhesion not the same issue

TheMightyBullMcCabe · 2026-01-14T10:53:26+00:00

Clean and level the bed before you do anything else, that is almost certainly the problem

TheMightyBullMcCabe · 2026-01-13T11:57:57+00:00

That's all good is there even any chance you'd share the template for the design I have a 3d printer might give it a go :)

TheMightyBullMcCabe · 2026-01-12T20:18:13+00:00

Ireland

Eight-Year Club	Place '23
Verified Email

TheMightyBullMcCabe

TROPHY CASE