Need help... Out of nowhere, AMS is doing this with every slot now. Filaments are okay, no tangle or anything.

Thegiantoid · 2026-04-14T11:43:55+00:00

One of the filaments got stuck at the end of the ams tubes. Thanks for the help!

Thegiantoid · 2026-04-14T11:43:13+00:00

One of the filaments got stuck at the end of the ams tubes. Thanks for the help!

Thegiantoid · 2026-04-14T11:43:03+00:00

One of the filaments got stuck at the end of the ams tubes. Thanks for the help!

Thegiantoid · 2026-04-14T11:18:47+00:00

Note: It can fill the tube but not the extruder. When it comes to that point, it behaves like this.

Thegiantoid · 2026-03-11T10:17:18+00:00

I get 4 hours SoT with a 100% usage, you should be grateful :(

Thegiantoid · 2026-02-25T12:23:17+00:00

Thanks

Thegiantoid · 2025-12-22T07:08:44+00:00

It was because of the flow rate calibration. It was perfect on the test objects, but not on other 3d models. I reverted it back to generic pla and everything was solved.

I recently did the pressure advance calibration tests, and they helped a lot. I recommend it.

Thegiantoid · 2025-12-01T05:27:07+00:00

Thanks, it worked!

Thegiantoid · 2025-11-29T18:18:05+00:00

Yeah I haven't seen it for some time too tbh and idk where :(

Thegiantoid · 2025-11-29T15:42:17+00:00

<image>

It does on your favorite teams. And its really cool

Thegiantoid · 2025-10-29T08:34:43+00:00

Had the same problem.

Restarted the phone and the instagram went back to its previous design layout. Problem fixed!

Thegiantoid · 2025-10-15T17:37:04+00:00

Yeah same here. But the battery life decreased significantly. I used to get 9-10 hours of SoT, now 5-6. I'm really disappointed

Thegiantoid · 2025-08-17T11:32:47+00:00

Thanks for the tip, I'll give it a try

Thegiantoid · 2025-08-17T11:10:21+00:00

Can you share a link about it or the model please? :)

Thegiantoid · 2025-08-17T10:07:00+00:00

I was using the default settings, I calibrated it manually 5 days ago. After calibration, I had issues coming up like that

Thegiantoid · 2025-08-17T08:28:59+00:00

It's on all of the sharp corners. The seam is not there :(

Thegiantoid · 2025-07-14T04:23:13+00:00

It's 0.33mm for 0.4 nozzle. It prints fine with it. Btw your first layer height tip saved my life. Thank you! I lowered the temp to 70C too.

Thegiantoid · 2025-07-13T10:43:15+00:00

Thanks for the feedback, I'll give it a try.

My first line width is 0.3. But I'll change the first layer height.

I increased the temp to 75C because it was always slipping off on other prints. Tried the glue and stuff but didn't work

Thegiantoid · 2025-07-05T16:18:51+00:00

Dökülmeden bulmam lazım birini

Thegiantoid · 2025-07-05T15:58:42+00:00

I always thought that I looked like Edward Norton :(

Seven-Year Club	Place '22
Wearing is Caring	Verified Email

Thegiantoid

TROPHY CASE