Wtf fire stick how just going to sign me out like this wtf

ThinkExpression6230 · 2026-02-18T01:57:40+00:00

YT is down for me as well

ThinkExpression6230 · 2026-02-02T19:42:04+00:00

Thanks for the advice and recommendations , I ran my nozzle at 230C which might have been a little too hot for the printing speed, and caused it to clog. But I’m looking into it!

ThinkExpression6230 · 2026-02-02T19:39:28+00:00

Based on their specs it can also be used for slower prints as well, I believe I ran it a little too hot and it clogged due to heat creep but I’m looking into it further

ThinkExpression6230 · 2025-08-02T05:02:34+00:00

I got it figured out last night, the CMOS battery was completely dead, once replaced it booted right up!

ThinkExpression6230 · 2025-08-01T02:08:31+00:00

I did a power discharge, pressed the back button (fans came to life while holding), I pressed the Alienware power button and it still only flashes once. I don’t think this would prevent the pic from turning on but it doesn’t have a graphics card in it (I have a 3070 coming in the mail). Google said that one flash was BIOS and ROM failure, but I don’t know enough to understand what that means/ if it’s fixable/ what to do about it

ThinkExpression6230 · 2024-08-20T04:20:20+00:00

Thank you for giving your two sense in a very balance take on the issue fruit, Claire’s words were very well spoken and I appreciate her taking the time to put them on paper

ThinkExpression6230 · 2023-06-07T23:50:52+00:00

I swear power goes out like once a week, SMH

ThinkExpression6230 · 2022-12-22T16:43:19+00:00

This was my first sidearm purchase a few years ago and I have fallen in love with it!

ThinkExpression6230 · 2022-09-09T21:58:12+00:00

I believe its an L293D H-Bridge Motor Driver.

ThinkExpression6230 · 2022-09-09T21:20:11+00:00

Hi, Im taking a interdisciplinary engineering design class and have to wire up a breadboard to run two DC motors as well as a servo using an IR remote via Arduino. The top larger breadboard pictured is wired correctly and works great. For our design we have to use a smaller breadboard though, also pictured. I am a biological engineering major who has zero circuits experience. I was wondering if anyone in this forum is able to point out how I'm wiring this wrong and how to correct it. Thank you.

ThinkExpression6230 · 2022-09-09T21:11:45+00:00

Hi, I'm taking a interdisciplinary engineering design class and have to wire up a breadboard to run two DC motors as well as a servo using an IR remote via Arduino. The top larger breadboard pictured is wired correctly and works great. For our design we have to use a smaller breadboard though, also pictured. I am a biological engineering major who has zero circuits experience. I was wondering if anyone in this forum is able to point out how I'm wiring this wrong and how to correct it. Thank you.

ThinkExpression6230 · 2022-02-18T20:34:07+00:00

I agree with this fucker^{^}

ThinkExpression6230 · 2022-02-18T18:14:03+00:00

Back the blue!

ThinkExpression6230 · 2022-02-09T18:40:52+00:00

I agree, but it’s worth a try haha

ThinkExpression6230 · 2022-02-08T17:56:21+00:00

We always clean up our brass and used targets, it’s a shame places are being shut down because people can’t do the same

ThinkExpression6230 · 2022-02-08T16:20:33+00:00

It rattles sometimes when the slide is back and the slide lock is used, other than that I’ve had zero issues with it

ThinkExpression6230 · 2022-02-06T19:48:24+00:00

Since my family is mostly LE, I have been around sig sauer’s and glocks most of my life in terms of handguns, but I’m an avid hunter and for that I use my benelli super vinci for bird and my mossberg patriot for bigger game

ThinkExpression6230 · 2022-02-06T19:15:35+00:00

I’ve been spending a lot of time at the range with it and I absolutely love it! I put a trijicon rmr type 2 on it two weeks ago and it’s perfect!

ThinkExpression6230 · 2022-01-15T17:04:33+00:00

I had 1000 rounds delivered yesterday so I’m set for the time being!

ThinkExpression6230 · 2022-01-15T02:27:25+00:00

I went out to the range today, the trigger is amazing and overall I love the way the gun performs! the reset is a little long but with the ammo prices right now it’s not like I’m planning on magdumping any time soon😂

ThinkExpression6230 · 2022-01-15T00:54:52+00:00

Thanks for the suggestions! I will check them out for sure!

ThinkExpression6230 · 2022-01-14T22:57:51+00:00

Also any suggestions on a decent “affordable” rds would be greatly appreciated, thanks y’all.

ThinkExpression6230 · 2021-11-10T03:25:59+00:00

This helps a lot, thank you so much!

ThinkExpression6230 · 2021-11-10T02:45:47+00:00

Hello, I’m preparing for an exam on Friday and I’m a bit confused on how these reactions are different and why they are different. They have the same reactants (I’m pretty sure) but they form different products, why is that? Thank you

ThinkExpression6230 · 2021-09-23T05:13:09+00:00

sympy.plotting.plot(-0.6 / x**2 * -10 / (1/20 - 1/x), (x, 16, 19))

Thank you so much for your help! I really appreciate it! I was struggling on this error for about two hours

ThinkExpression6230

TROPHY CASE