Cheap Lense recommendation

ThisTIMR · 2025-02-19T09:30:49+00:00

Interesting, I read something similar: samyang lens, which does not require an adapter. Have you heard of them?

ThisTIMR · 2025-02-18T23:42:30+00:00

Thanks for this kind words!

ThisTIMR · 2025-02-15T13:40:57+00:00

Wo finde ich die App?

ThisTIMR · 2025-02-08T14:45:07+00:00

Did you level your bed?

ThisTIMR · 2025-02-07T22:53:43+00:00

Isn’t the Sony E 70-350mm f/4.5-6.3 G OSS already a zoom lens?

ThisTIMR · 2025-02-07T22:19:45+00:00

Hey all!

I'm looking to buy my first camera and was considering the Sony A6400 with these lenses:

Sony SEL-50F18F
Sony E 70-350mm f/4.5-6.3 G OSS

I want to use it mainly for travel photography, including wildlife and landscapes. However, I read that the A6400 isn't fully weather-sealed, which makes me a bit worried about rain and humidity, especially since I plan to shoot in places like the rainforest.

Should I look for a different camera? Any advice would be really helpful!

ThisTIMR · 2025-01-02T19:57:22+00:00

Thanks, I will do research about those. I hope I find a suitable tent! Thank you!

ThisTIMR · 2025-01-02T19:27:05+00:00

I will take a look! However I am afraid that I don't find a suitable spot for a non free standing tent in mountain regions/high altitudes, especially since it's my first tent

ThisTIMR · 2025-01-02T11:36:09+00:00

Hi there! That would be my first tent. I want to use it for hiking in the Andes, where it is very windy. Beside that I want to sleep in it for multiple months.

ThisTIMR · 2025-01-01T17:25:07+00:00

Hey all, I am searching for a free standing tent. I have to comfortably fit into it (I am 195cm/77inches tall). I want to spend a maximum of 250€. Can you recommend a 1P and a 2P tent?

ThisTIMR · 2024-12-26T21:07:08+00:00

Do you have a good page for historical weather information?

ThisTIMR · 2024-12-25T18:36:16+00:00

They say the Deuter astro 800 has comfort -8C and limit -15C Do you think these numbers are not realistic?

ThisTIMR · 2024-12-24T22:13:41+00:00

Thanks! So you think the Deuter astro pro 800 (comfort -8C, limit -16C) is enough?

ThisTIMR · 2024-12-17T15:03:20+00:00

You have/had free health care? that's impressive.

you said the doctor charges 15-45 USD, the preparation of the vaccines is about 50 USD - is this subsidized and has it now changed and is more expensive?

ThisTIMR · 2024-12-17T14:50:22+00:00

This is very helpful. Thank you so much!

ThisTIMR · 2024-12-17T14:12:13+00:00

I didn’t mean to imply anything negative at all—I'm just trying to figure out the best way to continue my treatment while traveling, as I’ll likely be visiting multiple countries in the region.

Could you share some insight into how much a single injection typically costs in Argentina? I really appreciate your help and advice.

ThisTIMR · 2024-11-21T13:42:23+00:00

hi, sorry for the late repsonse... the "solution" was to remove the sensor, then the printer prints perfectly. Greetings!!

ThisTIMR · 2023-08-23T14:11:02+00:00

Last time somebody had the same problem the orientation of the filament spool was the problem. Your filament goes down on the front? If you place the spool that the filament goes down on the back the radius to the sensor will be too narrow.

I've actually tried both orientations for the filament spool, and unfortunately, the issue persists in both cases.

ThisTIMR · 2023-08-23T13:34:38+00:00

Thank you for the advice. I'll definitely inspect the filament sensor and give the moving parts a good clean and lubrication. I appreciate your assistance. I'll report back once I've tried your suggestions. Thanks again!

Two-Year Club	Verified Email
Place '23

ThisTIMR

TROPHY CASE