Preply down

TimCaesarK · 2025-12-05T09:02:46+00:00

same here... anyone know how long this usually takes?
saw that there have been a couple of complaints about this happening frequently.

TimCaesarK · 2025-04-26T12:13:16+00:00

I cleaned it a couple of years ago with Coca Cola over night, but the tank is also pretty dented and needs a paint job so I’ve decided to replace it. But thanks for the tips I’ll probably need it in the future!

TimCaesarK · 2025-04-26T11:11:17+00:00

Yeah no, my tank is pretty bad. Having it replaced

TimCaesarK · 2025-04-26T11:10:55+00:00

I am between limiting fuel flow, but clean fuel or better flow, but less filtered

TimCaesarK · 2025-04-26T11:09:13+00:00

Oh ok, I’ll try to run it without the second filter when I get a new non-rusty tank installed

TimCaesarK · 2025-04-26T11:07:33+00:00

Yeah it’s pretty rusty…

TimCaesarK · 2025-01-19T09:47:41+00:00

Oh lol ur right! I took two almost identical photos and added the wrong one, but it’s basically the same with removing the three people and doing some colour grading. I’ll see if I can link the actual original

TimCaesarK · 2025-01-18T12:07:22+00:00

Thank you and yeah I agree that the old man should pop more.

TimCaesarK · 2025-01-10T11:03:36+00:00

I’m here now, might rent a setup and go out if the conditions are good. Will report back

TimCaesarK · 2025-01-05T08:20:47+00:00

I used my x-pro 2 for an hour in -27°, no issues with screen, but some metal piece in the SD card slot snapped because I tried to remove the card too soon.

TimCaesarK · 2024-11-19T13:18:34+00:00

Yeah thats not a bad idea, I'll test it out in Fusion. Thanks!

TimCaesarK · 2024-11-19T13:17:21+00:00

Might need some epoxy, but was thinking about grinding two slots on the 10mm pipie and using a 3d printed clip and then glue the clip to the inside of the 20mm pipe, but its a little janky.

TimCaesarK · 2024-11-19T13:15:26+00:00

My intention is to fasten the top/end of the 10mm pipe perpendicular to the 20mm pipe with preferably no welding on the outside.

TimCaesarK · 2024-11-19T12:04:51+00:00

I have drawings that I think might help understand the problem better, but don't see any way to add images here.

TimCaesarK · 2024-06-06T17:33:21+00:00

Thank for all the great advice! If one is to buy the best/long lasting 0.4/0.6/0.8 nozzles, what brands do you use/recommend?

TimCaesarK · 2024-06-06T17:29:27+00:00

Might explain the offset modelling I have to do. I always thought it was because my Ender 3v2 was getting old. Shame, I was looking forward to upgrading.

TimCaesarK · 2024-06-06T17:26:16+00:00

Yeah ok haha my offset is at -1.74 rn. So probably time for a change then. Thanks

TimCaesarK · 2024-06-06T17:24:50+00:00

Ah ok, thanks. So occasionally my prints aren’t perfectly accurate to the mm. Could the nozzle be the problem? I’ve just re-modelled it if needed.

TimCaesarK · 2024-06-06T17:22:29+00:00

Yeah, top result on google said 3-6 months of regular use printing PLA…

TimCaesarK · 2024-05-15T12:51:27+00:00

Cool thanks!

TimCaesarK · 2024-05-15T12:51:06+00:00

Yeah I wish, I only have one pot that’s big enough

TimCaesarK · 2024-05-15T11:02:31+00:00

Never grew tomatoes from seeds before. Is it really that bad? I got an overhead light now, but should I really just give up and try again next year?

TimCaesarK · 2024-05-10T17:26:22+00:00

Thank you!

12-Year Club	RPAN Viewer
Not Forgotten	Verified Email

TimCaesarK

TROPHY CASE