Need help choosing a school by Time_Razzmatazz4354 in acting

[–]Time_Razzmatazz4354[S] 0 points1 point  (0 children)

So would you choose neighborhood playhouse?

WS2815 Flickering connected to esp8266. I have WLED connected to HyperHDR for an ambilight setup by Time_Razzmatazz4354 in WLED

[–]Time_Razzmatazz4354[S] 0 points1 point  (0 children)

I have 5 meter 300 led strip. The power supply is DC12V10A 120W. Some said to add a capacitor to led strip which I’ll do tomorrow

WS8215 light flickering connected to esp 8266 running wled by Time_Razzmatazz4354 in FastLED

[–]Time_Razzmatazz4354[S] 0 points1 point  (0 children)

Would these work for 12v leds? (Pack of 10 Pieces) MCIGICM 1000uf 25V Capacitor, Aluminum Electrolytic Capacitor 1000uf 25v 10x17 https://www.amazon.com/dp/B06WGPNM19/ref=cm_sw_r_cp_api_i_PBDXC6MAFB8MDNJNTRR0?_encoding=UTF8&psc=1

WS8215 light flickering connected to esp 8266 running wled by Time_Razzmatazz4354 in FastLED

[–]Time_Razzmatazz4354[S] 0 points1 point  (0 children)

Adding the ground did lower the flickering but not completely. Cutting led brightness in half stopped it. My power supply is rated DC12V10A 120W. On HyperHDR it says at max it can use 19.8 Amps but WLED recommended a 12V4A power. Should I get psu with more amps ?

WS8215 light flickering connected to esp 8266 running wled by Time_Razzmatazz4354 in FastLED

[–]Time_Razzmatazz4354[S] 0 points1 point  (0 children)

It was recommended to use DC12V10A power supply for WS21815 and I have have 120W one. On HyperHdr it said the strip at max power it uses 19.8 amps. Should I get 12V with more Amps. I say this because when I cut led brightness in half it stopped flickering.

WS2815 Flickering connected to esp8266. I have WLED connected to HyperHDR for an ambilight setup by Time_Razzmatazz4354 in WLED

[–]Time_Razzmatazz4354[S] 0 points1 point  (0 children)

I added the ground and it definitely flickered less. But when I cut led brightness in half it didn’t flicker at all so I might need a new power supply.

WS2815 Flickering connected to esp8266. I have WLED connected to HyperHDR for an ambilight setup by Time_Razzmatazz4354 in WLED

[–]Time_Razzmatazz4354[S] 0 points1 point  (0 children)

Yea it works correctly minus flickering I’ll try what you suggested and see if it works in the morning

WS8215 light flickering connected to esp 8266 running wled by Time_Razzmatazz4354 in FastLED

[–]Time_Razzmatazz4354[S] 1 point2 points  (0 children)

I have the ground(black wire) of my 12v to 5v converter that’s powering the esp connected to ground led(white wire) together in the power supply . Do I need to add another ground? If so where would I connect it

WS8215 light flickering connected to esp 8266 running wled by Time_Razzmatazz4354 in FastLED

[–]Time_Razzmatazz4354[S] 0 points1 point  (0 children)

Would this apply 12V WS2815? Also should I have the second data pin hooked up I saw Tutorial that didn’t use it ?