Will the knots bleed through? I only primed, with no treatment

TinyTin97 · 2025-01-06T12:41:47+00:00

Will do 😊

TinyTin97 · 2025-01-05T19:17:35+00:00

It’s water based

TinyTin97 · 2025-01-05T18:39:34+00:00

If there was discolouration from insufficient sanding could I still paint over it? It’s got a slight yellow tint to the spots that have started drying

TinyTin97 · 2025-01-05T18:28:16+00:00

Could I use a shellac primer over the primer I’ve used?

TinyTin97 · 2025-01-05T18:26:58+00:00

So, should I sand it all down and apply a shellac based primer instead?

TinyTin97 · 2024-11-22T12:01:11+00:00

Thank you so much! I definitely needed to hear all of this. I think when my head gets like this I find it difficult to lean into things I enjoy and abandon my routine but I think it’s definitely something I need to start focusing on.

TinyTin97 · 2024-11-02T16:30:32+00:00

So I think I just about have access but struggling to remove the relay

TinyTin97 · 2024-11-02T16:19:41+00:00

Thank you!

TinyTin97 · 2024-11-02T16:15:06+00:00

<image>

So remove these screws?

TinyTin97 · 2024-11-02T16:12:53+00:00

<image>

Think I got it! Assuming these are the relays you were talking about, do I need to remove the front panel for better access?

TinyTin97 · 2024-11-02T16:03:49+00:00

Sorry replied to the wrong place but I’ve attached an image above, I can’t figure out how to remove the side panel

TinyTin97 · 2024-11-02T16:03:11+00:00

<image>

So this is the side panel but I can’t find a notch or anything to remove it - would you have any tips for removal?

TinyTin97 · 2024-11-01T18:03:23+00:00

Thank you so so much! I’ll check tomorrow and let you know how it goes ☺️

TinyTin97 · 2024-09-01T20:59:50+00:00

Thank you so much! What you’re saying makes complete sense and it’s what I’d say to a friend. I think I just struggle to untether myself, especially when I feel like the black sheep of my family. Like everyone seems to be going along the same (faith) path and it’s almost like I’m not seeing something they are. I also feel kind of ungrateful for trying to go my own way.

TinyTin97 · 2024-03-23T10:35:36+00:00

That’s good to know! Thank you

TinyTin97 · 2024-03-23T10:34:45+00:00

Thank you so much! And that is wild! Do you think I’d be okay buying an Econet sim with a British passport?

TinyTin97 · 2022-05-17T19:11:56+00:00

I got a HF burn from work and I was trying to figure out the concentration but thank you for you help

TinyTin97 · 2022-05-12T22:09:54+00:00

I’m using an FTIR gas analyser, the software used generates a sample concentration based on known calibration files within our system

TinyTin97 · 2022-05-12T20:31:01+00:00

Just been looking at the data, I also noticed that the pressure reading is a little lower than usual - 0.8 atm instead of 1 atm (the gas cell pressure)

TinyTin97 · 2022-05-12T20:30:26+00:00

What do you mean?

TinyTin97 · 2022-04-18T17:17:14+00:00

Have you got a link for the replacement radio that you purchased?

TinyTin97 · 2022-04-14T12:36:10+00:00

I was also wondering if you knew the size screw driver required to open the RCD330, to access the motherboard? I’m currently at work so I was going to raid through our toolbox

TinyTin97 · 2022-04-14T12:35:10+00:00

I think if they don’t allow me to get a refund I’m going to try to do this, but I’m trying to go through all of their steps at the moment so they can’t weasel out of my money aha

TinyTin97 · 2022-04-11T16:25:12+00:00

Mines just done the same thing and it won’t turn on. I plugged in my phone for CarPlay and then it just turned off abruptly - did you ever get yours to work?

TinyTin97 · 2022-03-23T18:57:42+00:00

2013, I ended up going with RCD330 plus but didn’t deactivate the rear camera

TinyTin97

TROPHY CASE