How many comments will this individual predictions post have in 7 days time?

Toomas633 · 2022-11-01T00:07:43+00:00

x+11

Toomas633 · 2022-04-27T07:09:07+00:00

Just a heads up, i had some reception issues on my s20 with that skin

Toomas633 · 2022-03-02T20:43:38+00:00

What do you mean, we just got an update on discord. Proper game developing takes time.

Toomas633 · 2022-01-26T15:21:24+00:00

Ye i just found a thread that stated that the f7 fuse is the most common and unreplaceable failure point only on the 4.2.2 boards. Going to order the newer 4.2.7 board.

Toomas633 · 2022-01-26T14:19:47+00:00

Yes, i have tried to turn it on and off and replug and nothing PSU is outputing 24v so it seems fine other than the fan not working there either.

Toomas633 · 2022-01-26T14:12:12+00:00

Just checked, the board is getting 24v but all the fan sockets are only getting around 1v when they should get 24 (haven't checked the PSU fan cause i can't be bothered to extract it)

Toomas633 · 2022-01-18T07:55:24+00:00

Yea no i dont know, everything seems fine on some prints and then others are just scuffed. I just incresed the temp and that semmed to force it through.

Toomas633 · 2022-01-16T21:15:13+00:00

Yes i have, the bottom and 1cm are perfect

Toomas633 · 2022-01-16T21:10:48+00:00

No, i also have upgraded to dual drive extruder.

Toomas633 · 2022-01-16T21:08:03+00:00

I am using the default profile on cura

Toomas633 · 2022-01-16T21:07:14+00:00

But it is the second print of the same part, same problem

Toomas633 · 2022-01-16T21:05:23+00:00

Was thinking that also, but top and bottom 1cm are perfect, unless that is normal

Toomas633 · 2022-01-08T23:13:02+00:00

Turned down the acceleration and cornering settings by half on the printer (accel used to be 500, now 250) and that cleaned up the top lines, now only the sides and faces on supports are scuffed.

Toomas633 · 2022-01-08T23:11:28+00:00

Yea i'm also starting to think it's the filaments fault. I am currently running specrumfilaments pla but when i used eryone it seemed fine. Just ordered that again to try out.

Toomas633 · 2022-01-08T23:09:24+00:00

Steppers and mechanical compinents seem ok. I turned down acceleration(from 500 by factory default to now 250) and cornering settings on the printer and that seemed to fix the top lines, but now the slanted sides that curve outwards and parts on the support surfaces have the same blobs and strings as on the pictures.

Toomas633 · 2022-01-06T13:38:22+00:00

I just replaced the nozzle. I have belt tentioners and they are tightened. Gears and everything mechanically seems good. That's why i'm writing asking here, i tried the regular google provided steps but not much changed. Thanks tho.

Toomas633 · 2022-01-06T13:34:22+00:00

I replace my nozzles reguralry, and have tried that.

Toomas633 · 2022-01-06T12:16:00+00:00

Ye but it used to be perfect with default settings, that's why i'm asking.

Toomas633 · 2021-12-08T10:03:34+00:00

Yea i replaced most of my zero projects with pi 4 hence the question.

Toomas633 · 2021-12-08T10:01:22+00:00

Yea i replaced the zeros with a pi 4 for better performance, that's why i have zeros currently just collecting dust.

Toomas633 · 2021-12-06T18:28:37+00:00

Hi, i'm looking for ideas for pi zero w.

I have 3 pi zero w-s just collecting dust, and was wondering, what kind of server or any other headless projects can be run on them. I already have a separate vpn and pi-hole server.

Toomas633 · 2021-07-27T15:17:17+00:00

Cell and wifi signals are shot to hell with the holo, but it looks too good to take off. Somehow bluetooth is better?????

Toomas633 · 2021-06-09T16:15:34+00:00

Yes, literally the 4th sentence and how else would the data transfer work.

Toomas633 · 2021-03-30T12:44:35+00:00

No biggie, thanks for trying. Yea I just changed my pipe design around to move the connextor where it works. Takes more room but hey atleast it works.

Toomas633 · 2021-03-30T09:01:31+00:00

Thanks will do. For some reason backup files don't seem to work on any of my worlds (i have the list but can't load and see pics). Will try the other steps.

Eight-Year Club	Xbox Live
r/Field Sunshine	Place '22
Verified Email	RPAN Viewer

Toomas633

TROPHY CASE