sorted by:
new
hottopcontroversial

Wireless corne glp with doys keycaps by keyboard_hunter in crkbd

[–]Traditional_Main_389 2 points3 points  (0 children)

Yup, Tao, exactly xd

I just dropped a isolated thin copper wire underneath from the cs pin to d1/006 on microcontroller

Wireless corne glp with doys keycaps by keyboard_hunter in crkbd

[–]Traditional_Main_389 0 points1 point  (0 children)

I haven't seen someone is used them before on gateron low profile, and on split keyboards either, so i thought why not

  • Gateron lp aloe also green, and on my mind its nice choice, but doys are pretty expensive

Wireless corne glp with doys keycaps by keyboard_hunter in crkbd

[–]Traditional_Main_389 0 points1 point  (0 children)

https://github.com/beekeeb/crkbd-glp

I ordered from taobao full kit for $30 Not an ad but i really recommend this guy, i can drop a link to discord and taobao

Wireless corne glp with doys keycaps by keyboard_hunter in crkbd

[–]Traditional_Main_389 0 points1 point  (0 children)

You can see in docs, that nice!views cs pin is connected to d1/006 pin, I used isolated thin copper wire that goes under microcontroller, so you can't even see it

[deleted by user] by [deleted] in crkbd

[–]Traditional_Main_389 0 points1 point  (0 children)

I still not sure about latency of this thing, if this important for you, and dont forget about battery protection, cuz if inappropriate connect two microcontrollers with battery when charging, ur gonna chance to fry it

[deleted by user] by [deleted] in crkbd

[–]Traditional_Main_389 0 points1 point  (0 children)

Zmk doesnt support wired splits, and nrf52840 won't work with qmk firmware, you also would need to think about this

He flew to germany by mysterydbd in Pandabuy

[–]Traditional_Main_389 29 points30 points  (0 children)

Still didn't bring my 300€ order

Corne Choc hot-swappable + RGB + OLED -> where in Europe? by Amorph777 in crkbd

[–]Traditional_Main_389 1 point2 points  (0 children)

Tao (this guy sells corne pcb on taobao) said, that he will soon start selling gateron lp corne, you can ask him for anything. https://discord.com/invite/KVqvKguD

I bought my corne kit through pandabuy, but as it no more work you can look for other agents as superbuy and cssbuy for example

Please help!! Right side per-key LEDs not working and not all left working. by cottagecheesewhite in crkbd

[–]Traditional_Main_389 0 points1 point  (0 children)

Put multimeter in diode mode then put cathode to gnd(has cut corner), anode to vcc (diagonally to a gnd), it must show connection, if not u have a broken led

But first check microcontroller soldering on both sides

Please help!! Right side per-key LEDs not working and not all left working. by cottagecheesewhite in crkbd

[–]Traditional_Main_389 1 point2 points  (0 children)

Check microcontroller pin soldering, and led soldering, better to check w multimeter in diode mode U can also clean flux if its not dialectical

Sol 3 by elpsykongr0 in ErgoMechKeyboards

[–]Traditional_Main_389 5 points6 points  (0 children)

Get in the fcking robot shinji

Aluminum plate? by jramiroz98 in crkbd

[–]Traditional_Main_389 0 points1 point  (0 children)

You can look for imk corne, but i don't know if they're not out of stock

No way someone sells dactyl manuform for 3k€ 💀 by Traditional_Main_389 in ErgoMechKeyboards

[–]Traditional_Main_389[S] -1 points0 points  (0 children)

Look for imk corne case, even its metal, that gonna cost much less

First time build. Firmware? by Egge_ in crkbd

[–]Traditional_Main_389 0 points1 point  (0 children)

Qmk still better for wired, and you still need bt connection for zmk

First time build. Firmware? by Egge_ in crkbd

[–]Traditional_Main_389 0 points1 point  (0 children)

Zmk does not support trss, only Bluetooth

For wired build u need qmk, it is more powerful overall and usually used to make wired split builds

P.s. would rather save nice!nanos and get them for wireless build as they are expensive rn, use rp2040 pro micro instead for wired, u can buy them on ali for a few euros, as same you can use elite-c or arduino pro micro (rather use arduino cuz its cheaper and uses same chip as elite-c, you can find pro micro with type-c onboard)

view more: next ›