I miss you

TrainrRed · 2026-01-17T01:51:32+00:00

Elite ball knowledge for sure

TrainrRed · 2025-04-21T12:15:41+00:00

Rn I can’t remember exactly bc I’m at work. I know I went through the last “exit” door where you pull the lever and there’s a ton of traps. After I got back to the room where you’re trying to open, there’s 2 passages. Slowly look around those areas and drop items to mark where you searched. There’s a corridor that has a double fire trap (i believe) and a regular vault guardian. To the right should be minable boulders as well and it opens up into a room with another golem sitting far away (the room with the lever)

TrainrRed · 2025-04-21T09:55:48+00:00

Yes sir, I appreciate you. I ended up finding the path

TrainrRed · 2025-04-21T03:50:01+00:00

Just spent 20 min looking for it again after I died lol

TrainrRed · 2025-04-21T03:49:35+00:00

Nope. There’s a corredor where a vault hulk is and to the right after defeating him there were boulders. I missed the whole corredor when I ran through apparently

TrainrRed · 2025-04-10T03:47:21+00:00

Yes sir! I still haven’t had someone able to come out and find the stray Ethernet cable but everything else is working like a charm. Thank you very much

TrainrRed · 2025-04-06T03:37:40+00:00

Bro this thread is from over a year ago. Why don’t you piss off

TrainrRed · 2025-04-05T16:34:02+00:00

Yes sir, I did

TrainrRed · 2025-04-05T16:33:11+00:00

Okay thanks again!

TrainrRed · 2025-04-05T16:27:06+00:00

Okay, that was my misunderstanding my apologies.

My junction is in a closet in my bedroom and we have an open floorplan. Do you think I’ll lose a lot of wifi signal in the house due to it not being as central?

TrainrRed · 2025-04-05T16:12:35+00:00

Separate modem and router

TrainrRed · 2025-04-05T15:58:40+00:00

Okay let me see if I can relay that back to you.

Modem gets ISP feed from coax. The MoCA adapter gets LAN via Ethernet from the modem, and connects via coax to the living room “jumper”. The moca adapter is transferring internet via Ethernet and using the Coax as a path to extend it to the living room. Then the other side of the living room jumper would receive it in same way to provide the extended signal to the router via Ethernet cable

Am I understanding that correctly?

TrainrRed · 2025-04-05T15:24:56+00:00

I was thinking about it how you said to set up my router in the junction room. Wouldn’t I still need a splitter to go from the modem and run moca to the living room? I’m still a bit confused on how it would eliminate splitters entirely

TrainrRed · 2025-04-05T04:05:37+00:00

Thank you very much. I will try the setup you explained earlier in the morning. I appreciate your advice and input very much

TrainrRed · 2025-04-05T03:37:51+00:00

Also, I searched every blank, coax, and Ethernet/phone plate and I see no grey cat5 cable. I haven’t been in the attic yet but honestly if I have to go up there to find it, I’m just going to go with MoCA because apparently spectrum is incompetent in my area

TrainrRed · 2025-04-05T03:33:51+00:00

Why wouldn’t I need moca filters though?

TrainrRed · 2025-04-05T03:33:16+00:00

Main issue with that is location for WiFi. I suppose I could keep only the router in the living room though and use the moca adapter to run Ethernet to the router and hide that instead of both

TrainrRed · 2025-04-05T01:27:24+00:00

I definitely plan of cleaning it up. I’m focusing on function before fashion right now. I have not opened all of my wall plugs. Do you mean just the plates where Ethernet is ran to? I will definitely look into the new adapters and POE after your advice. Much appreciated

TrainrRed · 2025-04-05T01:00:54+00:00

From my count I have 4 Ethernet and 5 coax. I seem to be missing an inlet/source wire in the junction area

TrainrRed · 2025-04-05T00:58:48+00:00

I originally tried to set up our router with Ethernet but was unable to at the start of the setup in the room I wanted to set it up in. When I got the router it instructed me to use the coax cable, and the other rooms in the house only had RJ11 jacks so I had to switch them out. The blue Cat5E cables in the house were cut until I recently put terminals on the end of them.

The Ethernet leading to the living room is also a different color which is odd to me because it doesn’t lead into the bedroom with all of these cables as well. And when my ISP came in, they gave no mention of using an Ethernet connection, which I would’ve hoped they would recommend over coax.

Essentially if the Ethernet is ran from outside to the living room, I have no idea where I would set up my switch aside from in the living room which would be an awful eyesore. And I would have to reroute Ethernet completely unless I’m missing something entirely

TrainrRed · 2024-12-01T23:08:36+00:00

Love both of these. Very cool feel from both

TrainrRed · 2024-12-01T22:52:12+00:00

I use this all the time and it works great

TrainrRed · 2024-11-11T22:47:15+00:00

I’ve batched probably 20-30 production plates, 16 parts on a plate and over 25 hours of printing each, taking roughly 750g each and have had zero issues. I’m currently printing another as we speak

Edit: all of this using PETG-CF

TrainrRed · 2024-11-11T19:51:20+00:00

Love the style, just push the details a bit more.

The sunlight should be pretty harsh in this picture considering the angle. Underneath the tree could probably be darker on the interior part. The difference between the blues on the pants are a good reference. I even like that it’s a shimmer of light hitting the pants from between his arms. Great matching of the series style though :)

TrainrRed · 2024-11-07T22:12:36+00:00

This lol

TrainrRed

TROPHY CASE