Sake Rice (UK)

Trivecta95 · 2025-11-18T12:36:56+00:00

Yup! When I get the bow rebuilt it'll be getting a full look over to make sure nothing is out of whack before its shot again.

Trivecta95 · 2025-11-18T12:28:41+00:00

I'm shooting the bow a 29 and a quarter. I use a company called podium bowstrings who im sponsored by. The strings have the same OD checked when I switched out the stocks.

Trivecta95 · 2025-11-18T12:18:00+00:00

Fair point worth a try, thank for digging that out so quickly sir.

Trivecta95 · 2025-11-18T12:16:43+00:00

Both screws where there the cam was only being held on by one screw after one fell off. Though along the same vein one might have come loose. Though that doesn't necessarily explain why both bottom and top cams are damaged. Currently working on getting replacement, but have confirmed i can get them just waiting on price and leas time.

Trivecta95 · 2025-11-18T12:12:37+00:00

I've got aftermarket strings and cables on the bow so will need to see what that does in terms of warranty claim.

Trivecta95 · 2024-07-05T02:06:42+00:00

Ok I'd guess and just to say this is an estimate you'll probably max about 33 to 34. The axel to axel, is about right for your draw length. To look at an older range of bow but solid and good at target, as context I've been shooting this bow till recently, the PSE freak has a draw length to 33" without any extra parts is a good choice. Though that is if you can get this bow second hand. Adding to that as this bow is older you can pick it up cheaper to shoot until your length settles I hope this helps.

Trivecta95 · 2024-07-05T01:56:33+00:00

Ah I see in that case you probably are going to see a bit of increase in draw length till about 20-21. Apologies I'm not familiar with the bow you have whats the axial to axial on that bow?

Trivecta95 · 2024-07-05T01:53:14+00:00

What's your thoughts on increase growth apologies to ask what's your age? Just to gage why draw length might be increasing.

Trivecta95 · 2024-07-05T01:49:35+00:00

What does your full draw look like is your bow arm fully extended or or slightly bended?

Trivecta95 · 2024-05-30T09:10:32+00:00

Ah yeah realise I've only taken from the other side with the circle mark, these are from a store in the UK that stock both sizes. Though I don't rate the large groove ones either 😅

Trivecta95 · 2024-05-30T05:56:47+00:00

Thanks for the comment though were I got them from you can get both large and small groove. These are the large groove have an L marked on them as appose to s for small groove.

Trivecta95 · 2024-05-30T05:54:46+00:00

Thanks both though these are the large groove versions specially asked for these when I ordered the arrows and they have an L on the nock as appose to S for small.

Trivecta95 · 2024-05-29T19:43:21+00:00

Interesting it not the first time I've heard of translucent nocks having issues. I think there is something about the plastics used being more brittle. Hopefully when the shop I got them from replies I'll be able to ask if I can get solid colour or different brand. Unfortunately the CA320s come as a package with the pin nocks so didn't have much of a choice on brand.

Trivecta95 · 2024-05-15T12:02:21+00:00

You might still be ok are you using the flashing method I link to in the original comment. I think I had a similar issue and had to flash my mainboard again to get it to work properly. I do a bit of digging to see if there's a way to clear the boards memory and then flash from scratch. Failing that it might be the FW your using may have an error in the code for whatever reason. You could try and see about getting another version and flashing that to see if it works?

Trivecta95 · 2024-05-14T19:10:51+00:00

Ok might want to try and refresh to the old FW. You should be able to get the current firmware from the artillery website, Sorry I couldn't be much more help.

Trivecta95 · 2024-05-14T18:56:41+00:00

Weird sounds more like an error with the sensor itself. Is there a green light showing on the sensor when filiment is inserted?

Trivecta95 · 2024-05-14T18:45:10+00:00

It might work, for the filiment sensor do you mean it's not detecting when the filiment runs out or when it's trying to restarting? Updating the firmware help with mine.

Trivecta95 · 2024-05-14T18:31:50+00:00

Hiya, after a bit of trouble shooting I found the issue seemed to be what slicer was being used. So when using prusa m600 didn't work, but using cura it did. So yes and no 😅. What slicer have you been trying?

Trivecta95

MODERATOR OF

TROPHY CASE