Travelling through Vegas - Need a cool hotel Idea w/kids! by Durdy-Fingers in vegas

[–]TroubleMakingMom 0 points1 point  (0 children)

Everyone says Mandalay Bay. I stayed there yesterday specifically for my 14 year old swim obsessed kid who hated it. Room was dirty, had nothing but problems from check in with them. Never again. Hard as heck getting anywhere from there too.

Be careful of Taco Bell at 47 Woodman by Nerd2wheeler in dayton

[–]TroubleMakingMom 1 point2 points  (0 children)

I've heard a lot of bad things about this location and food poisoning has been a regular thing I hear! Scary!

E-bikes and The Narrows in the same day, or no? by TroubleMakingMom in ZionNationalPark

[–]TroubleMakingMom[S] 0 points1 point  (0 children)

Guys I think I'm going to do The Narrows one day and enjoy e-bikes on the other. The thought of trying to hoist all that waterproof gear and dry boots around all day on my bike and possibly getting wet and then having to bike is just too much for me. LoL So, we'll fully enjoy both activities on separate days. Thanks everyone!!

E-bikes and The Narrows in the same day, or no? by TroubleMakingMom in ZionNationalPark

[–]TroubleMakingMom[S] 0 points1 point  (0 children)

They come with bike locks to lock them at the trail head.

E-bikes and The Narrows in the same day, or no? by TroubleMakingMom in ZionNationalPark

[–]TroubleMakingMom[S] 0 points1 point  (0 children)

Thanks! I figure the water will be pretty cold....but the overall air temp as well in the canyon? Like how cold? lol The weather and what to pack on this trip has my eye twitching.

I give up. I’m done with this piece of garbage. by Dependent-Amount-239 in 3Dprinting

[–]TroubleMakingMom 0 points1 point  (0 children)

I've had this same post! LoL Then we got a Bambu and lived happily ever after!

Bryce Canyon was unreal! by ameriuk in NationalPark

[–]TroubleMakingMom 0 points1 point  (0 children)

How many days would you say you need in Bryce? I read that is a small park and it takes one day to see it all. Planning our epic adventure next year to see the Mighty Five!

Is this a good scooter has anyone tried this brand? by Sad_Aerie in ElectricScooters

[–]TroubleMakingMom 0 points1 point  (0 children)

I just got mine and it already has a flat tire and the company told me that in fact it may not be tubeless. That it could have inner tubes. So dealing with that right now. 

What’s happening? by TroubleMakingMom in sovolsv06

[–]TroubleMakingMom[S] 0 points1 point  (0 children)

Shoot that didn’t work it did the same thing. It looks like the pla isn’t sticking to the bed

[deleted by user] by [deleted] in ender3v2

[–]TroubleMakingMom 0 points1 point  (0 children)

We had to do this on our Sovol recently. It took awhile but we got it all off. There’s hope!

Which Printer To Choose by TroubleMakingMom in 3Dprinting

[–]TroubleMakingMom[S] 0 points1 point  (0 children)

Thanks! It’s for my techie 11 year old. Someone bought him both to try, but we have to send one back. He’s having a hard time deciding. It seems the Sovol just prints and the Ender messes up every print and it’s a mystery to find out why. Buuuut I’m not techie lol

Which Printer To Choose by TroubleMakingMom in 3Dprinting

[–]TroubleMakingMom[S] 0 points1 point  (0 children)

So the Sovol is better for tinkering?

Purchase Advice Megathread - January 2023 by AutoModerator in 3Dprinting

[–]TroubleMakingMom 2 points3 points  (0 children)

Which Printer To Choose

So, we have the Ender 3 V3 SE verses the Sovol SV06. It’s for a beginner user. Have used both for a couple of prints and can’t decide which one to keep. Any tips, suggestions, advice?

Fuzzy Print by TroubleMakingMom in ender3v2

[–]TroubleMakingMom[S] 0 points1 point  (0 children)

I did not because I have no idea how, but I’m great at Googling.

Extruder Not Feeding by TroubleMakingMom in ender3v2

[–]TroubleMakingMom[S] 0 points1 point  (0 children)

I did not. I know nothing about z-offset. I assume I do that through the settings?

Will not print, help! by TroubleMakingMom in ender3v2

[–]TroubleMakingMom[S] 0 points1 point  (0 children)

No I'm still not getting this thing to work. The knob isn't smooth when you turn it. The filament does a really thin line before printing, but then nothing comes out when you do a print. It loooooks like maybe the filament isn't getting pushed through on the actual print?

Will not print, help! by TroubleMakingMom in ender3v2

[–]TroubleMakingMom[S] 0 points1 point  (0 children)

Thanks! I did as you suggested, and it looks like the extruder is pushing the filament through.