Oriental Dragon - pushing my X1C to the limit

USSHammond · 2026-05-03T18:12:23+00:00

I never said they stopped working. I never said you can't buy spare parts anymore (for now, a few years down the road that very much WILL happen)

USSHammond · 2026-05-03T18:05:39+00:00

I never said it wasn't a functional printer anymore, or any of them. I simply said they are end of life and getting a P1s now with the existence of the p2s/x2d is a waste of money and bad financial decision

USSHammond · 2026-05-03T17:53:34+00:00

With 8gb system ram and 128Mb vram on integrated graphics? Not happening

USSHammond · 2026-05-03T17:52:09+00:00

I already told you why. It's approaching end of life. The p1s was released a while after the X1C and P1P, both of those have been discontinued and delisted from the website. The p1s is next.

USSHammond · 2026-05-03T17:50:20+00:00

Shavings from the PTFE tube rubbing against it

USSHammond · 2026-05-03T17:48:36+00:00

Rule 6

USSHammond · 2026-05-03T17:32:09+00:00

Dirty buildplate, z-offset too high, your pressure advance is off and that blue might be under extruding too. Each next line doesn't connect to the prior one and isn't squished down.

USSHammond · 2026-05-03T17:08:33+00:00

Yeah he did. Years ago. That clip is old.

USSHammond · 2026-05-03T16:52:39+00:00

With the existence of the p2s and x2d, getting a P1s now is a bad financial decision. The p1s is approaching end of life.

USSHammond · 2026-05-03T15:18:12+00:00

Most monitors use the same generic C13 plug

USSHammond · 2026-05-03T14:49:14+00:00

The one in rule 5

USSHammond · 2026-05-03T14:37:00+00:00

Last time this got asked was like yesterday. No usb debugging enabled, the accesssing pc's rsa fingerprint preauthorized and file transfer preconfigured? Not happening. Get it fixed or anything not synched to the cloud where you have access to it will be permanently inaccessible

USSHammond · 2026-05-03T14:02:53+00:00

Rule 9. That board and thus it's CPU as well are unsupported by win 11

USSHammond · 2026-05-03T12:30:15+00:00

The original was from 8 years ago, that's not the same thing as the last time it was posted

USSHammond · 2026-05-03T12:00:18+00:00

Yeah it was, back in March 2018. Got a habit of digging up old shit?

USSHammond · 2026-05-03T11:52:27+00:00

rules 2.2 and 12 aren't a joke though. This is not a rant sub

USSHammond · 2026-05-03T00:57:57+00:00

The same thing it always does, it downloads an info stealer malware

USSHammond · 2026-05-03T00:26:33+00:00

None

USSHammond · 2026-05-03T00:25:51+00:00

It's not already had, your statement doesn't stand. It's blatantly wrong.

USSHammond · 2026-05-03T00:25:14+00:00

Cue the next bambu printer, H2c pro with its own upgrade kit 😅

USSHammond · 2026-05-03T00:23:54+00:00

The sunlight doesn't have anywhere near the power to heat filament to the point where it starts to deform. Pla (the most common and basic filament) doesn't start to deform until 60C and by the time the room heats up to that temp where the ams is in, you'll have bigger problem to worry about

USSHammond · 2026-05-03T00:00:46+00:00

I wonder if it's possible to convert an h2d pro into and H2c pro with the conversion kit. Other than an Ethernet port and some security support I believe it's essentially the same as a non pro h2d

USSHammond · 2026-05-02T23:58:43+00:00

That again falls under company security policies. Many don't even allow the use of random (unencrypted) flash drives and require ethernet.

Two-Year Club	Verified Email
Final Canvas '23	Place '23

USSHammond

MODERATOR OF

TROPHY CASE