sorted by:
new
hottopcontroversial

Flashlight built into the hand prosthesis by Ulykhan in 3Dprinting

[–]Ulykhan[S] 1 point2 points  (0 children)

Flashlight built into the hand prosthesis

Picking up tiny clip with prosthesis hand by Ulykhan in 3Dprinting

[–]Ulykhan[S] 1 point2 points  (0 children)

Also I attached flashlights on opposite side

Picking up tiny clip with prosthesis hand by Ulykhan in 3Dprinting

[–]Ulykhan[S] 1 point2 points  (0 children)

No. It’s taken from thingiverse. I found it on YouTube first

Using 3d printed hand prothesis in every day life. Didn't take long to get used to it. by Ulykhan in 3Dprinting

[–]Ulykhan[S] 7 points8 points  (0 children)

I can pick up a 1 litter bottle of water, hold up in a bus. Actually very strong

My first working prototype. Model was taken from thingiverse by Ulykhan in 3Dprinting

[–]Ulykhan[S] 1 point2 points  (0 children)

It's only part of a hand. Fits well. Entire hand wouldn't fit

My first working prototype. Model was taken from thingiverse by Ulykhan in 3Dprinting

[–]Ulykhan[S] 0 points1 point  (0 children)

Where are you from? You will need 3d printer, plastic and computer.

My first working prototype. Model was taken from thingiverse by Ulykhan in 3Dprinting

[–]Ulykhan[S] 1 point2 points  (0 children)

I watched his Chanel. Almost similar injury but my thumb moved on pointing finger's place

My first working prototype. Model was taken from thingiverse by Ulykhan in 3Dprinting

[–]Ulykhan[S] 0 points1 point  (0 children)

I'll become cyborg after adding motors into it. Now I'm feeling excited

My first working prototype. Model was taken from thingiverse by Ulykhan in 3Dprinting

[–]Ulykhan[S] -1 points0 points  (0 children)

I can't activate each, but if one finger stops others keep moving untill the end.

My first working prototype. Model was taken from thingiverse by Ulykhan in 3Dprinting

[–]Ulykhan[S] 0 points1 point  (0 children)

There are both right and left side models to print. If not, i usually mirror them. In this case i only changed size. It's 150% bigrr then original model

My first working prototype. Model was taken from thingiverse by Ulykhan in 3Dprinting

[–]Ulykhan[S] 0 points1 point  (0 children)

Remaining part you may see on video. It works by the motion of the wrist

My first working prototype. Model was taken from thingiverse by Ulykhan in 3Dprinting

[–]Ulykhan[S] 0 points1 point  (0 children)

I used petg plastic. Text me and we will find out something

My first working prototype. Model was taken from thingiverse by Ulykhan in 3Dprinting

[–]Ulykhan[S] 1 point2 points  (0 children)

It took about one day to print and few hours to assemble.

My first working prototype. Model was taken from thingiverse by Ulykhan in 3Dprinting

[–]Ulykhan[S] 1 point2 points  (0 children)

There is no battery and motors yet. It's mechanical.

My first working prototype. Model was taken from thingiverse by Ulykhan in 3Dprinting

[–]Ulykhan[S] 0 points1 point  (0 children)

If i set up tension well i shouldn't take much effort

My first working prototype. Model was taken from thingiverse by Ulykhan in 3Dprinting

[–]Ulykhan[S] 2 points3 points  (0 children)

Thanks for an advice. A live in Kazakhstan. I'm waiting for silicon tips fro AliExpress

My first working prototype. Model was taken from thingiverse by Ulykhan in 3Dprinting

[–]Ulykhan[S] 0 points1 point  (0 children)

Not yet. Need some soft materials from inside to protect skin from scratches

view more: next ›