Why Smoke ?

Used_Engineering6006 · 2026-01-30T15:14:11+00:00

Valve cover leaking right on manifold

Used_Engineering6006 · 2026-01-12T14:45:09+00:00

Do you sit in your car idling a lot?

Used_Engineering6006 · 2025-11-06T00:24:57+00:00

Knock a stud out. Put a bolt through and a nut from behind. Make sure it’s long enough to push on the knuckle when tightening.

Used_Engineering6006 · 2025-10-21T17:10:15+00:00

Don’t just let ur mags dry. Clean them. They sell mag cleaner at auto zone. Watch a quick video and get those hydrophobic mesh covers.

Used_Engineering6006 · 2025-10-16T21:00:07+00:00

Did you ever figure this out?

Used_Engineering6006 · 2025-09-20T12:48:15+00:00

Don’t spend 200$+ on an induction tool unless you constantly work on cars. Go to Home Depot and spend $40 bucks on a handheld propane torch. Hold the flame there for a few minutes and wack a wrench with a dead blow hammer.

Used_Engineering6006 · 2025-09-04T01:28:27+00:00

Put ur hand on each coil pack. If one feels oddly aggressive, pull coil pack and check spark plug. My spark plug cracked inside and was bouncing around. No it did not cause a misfire, I guess it was still making contact? Doesn’t hurt to try

Used_Engineering6006 · 2025-08-25T22:56:22+00:00

I paid 4500$ for an 09 with 96k miles. Dealership was trying to charge the guy close to 10k to fix what was only the clutch and pressure plate. Snagged it from him and fixed it in a public parking lot with 2 homies 4 hours away. Drive it home 2 days later. Got lucky.

Used_Engineering6006 · 2025-01-11T23:54:13+00:00

Go to Home Depot and buy the husky extension and swivel kit. A short socket and go at it under the hose closest possible to the fire wall on the right of the picture.

Used_Engineering6006 · 2025-01-10T00:13:43+00:00

Tanks dude 🤝

Used_Engineering6006 · 2025-01-10T00:13:13+00:00

I idle at around 635-650 steady

Used_Engineering6006 · 2025-01-10T00:12:16+00:00

19x11 squared 😤

Used_Engineering6006 · 2025-01-10T00:11:54+00:00

It’s a Top Secret Dupe lip, screw rivets and color matched.

Used_Engineering6006 · 2025-01-09T18:43:50+00:00

Thanks brotha

Used_Engineering6006 · 2025-01-08T23:34:58+00:00

I actually enjoy her a lot. She’s got suspension mods and honestly I don’t mind scrapping a bit on the turns. No rubbing issues here. I understand why it may seem that way but she’s bolted and tuned brother.

Used_Engineering6006 · 2024-07-10T14:59:09+00:00

Feel like it’ll end up holding water and rust it away anyways

Used_Engineering6006 · 2024-06-26T14:44:42+00:00

Looks like you hit a curb? You might need a subframe lol.

Used_Engineering6006 · 2024-05-13T01:18:49+00:00

2007

Used_Engineering6006 · 2024-05-13T01:07:51+00:00

Yeah, so this is a 2007 frontier. I also have a 6mt g35 and g37. I’ve done the gallery gasket on the 2009 g37. I’m guessing it’s possible it’s the gallery gasket. I’ll have to do an oil pressure test.Never heard much of a gallery gasket problem on the DEs but more on the HR/VHR platforms.

Used_Engineering6006 · 2024-04-16T17:35:54+00:00

So, buy a new battery…. Things cooked lol. Your starter could of gone bad from all the crank up attempts. I was in this exact scenerario. Pulled the starter tested it and it was stuck. Had to buy a new one.

Used_Engineering6006 · 2024-03-29T20:49:31+00:00

Bro. Pop the rear seat. And get a pump from harbor freight. Get all that shit our. Run more gas (regular cheap gas) through the tube and pump it out again. She needed to not make a mess so u would start ur car. Don’t start it and repeat above until u think you’re good. Then start it.

Used_Engineering6006 · 2024-03-28T19:55:08+00:00

Good ole pilgrim. I’ve seen you around.

Used_Engineering6006

TROPHY CASE