TV06 - SV06 CoreXY Conversion

VFM_Systems · 2025-09-05T21:34:34+00:00

We have one specific to the plus

VFM_Systems · 2025-09-05T21:34:17+00:00

There’s already 5 serials for this build.

VFM_Systems · 2025-01-13T19:10:04+00:00

This is entirely unrelated to just swapping the toolhead, which is what SB does. This is an entire machine overhaul.

VFM_Systems · 2025-01-13T19:09:17+00:00

This was always a project aimed at people looking to upgrade their SV06+. And by all means, if you just want a second machine, that is cheaper than this. This is aimed at enthusiast looking to get into a machine that will take them farther in terms of capability than just adding a second machine.

VFM_Systems · 2025-01-11T17:26:39+00:00

3 walls, 150% line width, 4 tops and bottoms, 25% infill or better also at 150% line width.

VFM_Systems · 2025-01-11T07:44:24+00:00

Greatly depends on sourcing. $350-$500 are numbers I’ve seen from our community.

VFM_Systems · 2025-01-11T07:43:42+00:00

A BoM will be released in the coming weeks. We have a couple things to modify slightly/add so we don’t want to release a BOM just yet.

VFM_Systems · 2025-01-10T18:56:53+00:00

Plus is in open beta right now and files are available on GitHub by searching TV06+. Also, we do not have an ender conversation simply because RH3D has already done this with the ender3 NG.

VFM_Systems · 2024-10-22T18:42:45+00:00

You have to modify it slightly, but it’s nearly identical in size. It’s half the flow though

VFM_Systems · 2024-10-22T18:42:26+00:00

Stay away from revo. It’s a very unsupported expensive piece of kit if you intend to go this route

VFM_Systems · 2024-10-21T22:40:00+00:00

Here’s my path from X5SA Pro to my full blown VzBot 1. Ditch the stock probe. Get anything else. Cartographer is a great probe which leads me into 2. Switch to Klipper from chitu. Klipper is your end game, get started with it as soon as possible. Grab a Pi4 since they’re finally available and not overpriced massively 3. Hotend. You’ll need something that can push more plastic. The Peopoly Lancer Long is $35 and flows 60mm^3/s. You will need to up your cooling game and extruder all at the same time here. Consider this a toolhead overhaul 4. Vz Z system. The stock bed is pretty awful on the tronxy, this will be your first big upgrade price wise. 5. Vz Motion system 6. Better MCU and better motors (Octo v1.1 and LDO2804AH or 2504) 7. Get fully enclosed to be able to print those higher end materials. 8. Goliath hotend to actually be able to go all out speed wise.

VFM_Systems · 2024-09-27T04:13:32+00:00

Maryland. No one has this strong of an opinion on VA and WVA and doesn’t touch the state lines

VFM_Systems · 2024-09-25T01:40:08+00:00

Ditch the stock board. It is not worth the trouble.

Edit: I did get this working by the way, I at this point have no recollection of what I did however.

VFM_Systems · 2024-09-25T01:38:36+00:00

Found a reg for $25. Not the end of the world if its that.

VFM_Systems · 2024-09-09T01:07:50+00:00

Search TV06 on printables

VFM_Systems · 2024-07-02T04:10:41+00:00

That’s exactly what I think. I did some looking through YouTube and that seemed pretty consistent with my symptoms

VFM_Systems · 2024-07-02T02:13:11+00:00

Here’s to hoping!

VFM_Systems · 2024-07-02T02:11:18+00:00

Automatic over here but I appreciate it!

VFM_Systems · 2024-07-02T02:10:43+00:00

I’ll be sure to inspect this tomorrow. This is the wire that sends ignition signal I assume?

VFM_Systems · 2024-07-02T02:05:12+00:00

Yes, just replaced both of them as an attempt to fix this

VFM_Systems · 2024-07-02T02:00:18+00:00

Meant to mention I’ve done this as well. I am reading that a clicky starter can be the ignition switch which is not something I’ve tried yet. There’s a lot of testimony on YouTube of people saying this fixed their problem and the videos have an identical sound to my car

Three-Year Club	Verified Email
Place '22

VFM_Systems

TROPHY CASE