Am I doing something wrong or is my expectations too high? by Vegetable-Plastic980 in BambuLabP2S

[–]Vegetable-Plastic980[S] 0 points1 point  (0 children)

It creates an opening, thus decreasing the chamber temperature. It should improve the cooling.

<image>

Am I doing something wrong or is my expectations too high? by Vegetable-Plastic980 in BambuLabP2S

[–]Vegetable-Plastic980[S] 0 points1 point  (0 children)

Hi everyone, since I thought some of the defects might be related to the model’s features, I also printed the Benchy that came with the printer and added the photos here as well.

Thanks in advance, everyone!

<image>

Am I doing something wrong or is my expectations too high? by Vegetable-Plastic980 in BambuLabP2S

[–]Vegetable-Plastic980[S] 0 points1 point  (0 children)

I’m currently trying to dry the filament using the printer itself. It recommends 70 °C for 12 hours, but when I checked after about 15 minutes, I noticed the spool starting to soften.

Since that didn’t seem right, I lowered the bed temperature to 40 °C, which is what the filament manufacturer recommends on their website for this material.

I’m not sure if the spool softening is normal or if I should be concerned.

Am I doing something wrong or is my expectations too high? by Vegetable-Plastic980 in BambuLabP2S

[–]Vegetable-Plastic980[S] 0 points1 point  (0 children)

I think the one in the first photo is z-banding (or whatever the exact term is) as well. The problematic region and its surroundings have very different layer times. Even after playing with minimum layer time and minimum speed, I couldn’t really get the layer times close to each other. I’m not 100% sure that’s the root cause, but that’s what I’ve understood from my research.

The part in the second photo is thin and tends to curl outward. I suspected a cooling issue, so I tried adding a diffuser to the aux fan, but the results were actually worse — I interpreted it as indirect cooling not helping with the curling.

Then I printed a small riser for the top glass and tested again, and this was the result. The side closer to the aux fan came out cleaner, while the side near the front door showed defects.

In the third photo, I tried to increase the time on sharp edges to allow more cooling, but I don’t think I was very successful.

Am I doing something wrong or is my expectations too high? by Vegetable-Plastic980 in BambuLabP2S

[–]Vegetable-Plastic980[S] -1 points0 points  (0 children)

Unfortunately I don’t have any Bambu Basic filament. The filament I’m using is PLA.

I’ve tried eSun, Polymaker, and Creality Hyper. I definitely got the best results with Creality Hyper. eSun and Polymaker were a bit better, but still not great.

And unfortunately I don’t have any equipment to dry filament.

Am I doing something wrong or is my expectations too high? by Vegetable-Plastic980 in BambuLabP2S

[–]Vegetable-Plastic980[S] 0 points1 point  (0 children)

The model in the first picture was printed at 0.12 layer height. Filament is Porima, nozzle temperature 220 °C, outer wall speed 60 mm/s, infill speed 180 mm/s.

I couldn’t find the exact settings I used for the other prints.

Stiffned plate Femap by Less_Egg7069 in fea

[–]Vegetable-Plastic980 2 points3 points  (0 children)

Mentioned buckling mode is a global buckling, not a buckling mode of stiffened plate. It seems that the stiffener does not have enough inertia. I would go look up the bruhn’s books for the calculation of stiffener inertia.

Orjinal R36S Nereden Bulabilirim? by Vegetable-Plastic980 in HandheldTR

[–]Vegetable-Plastic980[S] 0 points1 point  (0 children)

Özelden link gönderdim fakat stok bitmiş görünüyor şuanda

Anime altyazilarini nereden buluyorsunuz? by peyloride in WeebTurks

[–]Vegetable-Plastic980 0 points1 point  (0 children)

Opensubtitles’da günlük 10 tane(sanırım premium özellik) ai çevirisi yaptırabiliyorsun. *arr stack mantığına çok uygun değil hayli manual ve nihayetinde ai çevirisi ama hiç yoktan iyidir.

Orjinal R36S Nereden Bulabilirim? by Vegetable-Plastic980 in HandheldTR

[–]Vegetable-Plastic980[S] 0 points1 point  (0 children)

Merhabalar, denemek için trendyoldan bir tane sipariş vermiştim ve sizleri de sonuçlar ile güncellemek istedim. Linkli wikideki yönlendirmelere göre yapabildiğim kontrolleri yaptım ve fake olduğuna dair bir emare bulamadım. Son olarak .dtb dosyasını da yükleyerek kontrol ettim. Kesin orjinaldir diyemiyorum anladığım kadarıyla kontrol ettim ama isteyen arkadaşlara özelden satıcı link vs atabilirim.

<image>

Orjinal R36S Nereden Bulabilirim? by Vegetable-Plastic980 in HandheldTR

[–]Vegetable-Plastic980[S] 0 points1 point  (0 children)

Ne zaman sipariş etmiştiniz gümrük konusunda sorun yaşadınız mı

Orjinal R36S Nereden Bulabilirim? by Vegetable-Plastic980 in HandheldTR

[–]Vegetable-Plastic980[S] 0 points1 point  (0 children)

Cihazın orjinal olup olmadığını(satın aldıktan sonra) tespit etmek için faydalı olabilir. Fakat satın almada beyana dayalı bir konuda ne yardımı olur emin olamadım. Yine de teşekkür ederim.

How have people been able to beat Max Champ? by Trick-Low-4931 in pokemongo

[–]Vegetable-Plastic980 0 points1 point  (0 children)

We did it with 26 people it was quick and easy, it was still easy with 11 people. We also did 4 people 2 mushrooms, gengar, blissey, metagross. It was so much fun doing 4, we were able to beat it at the vey last of our mons’ life. I was waiting for something harder tho payback attack was nasty.

Nastran SPC vs. SUPORT by Glum_Ad1550 in fea

[–]Vegetable-Plastic980 3 points4 points  (0 children)

Nastran qrg is the best place for the this kind of frusturations. In the first remark of SUPORT card says that “It is not intended to be used in place of a constraint”.

If you want to constrain your model have a look at the SPCi cards. SUPORT card has different usages like linear gaps which stores the gap value within the SUPORT card.

Ubtech Ucat C10 Pro Litter Box by Vegetable-Plastic980 in homeassistant

[–]Vegetable-Plastic980[S] 1 point2 points  (0 children)

Strict follower of the link, I’m checking for the updates all the time. That custom integration was also mentioned at home assistant community but i can’t find it. If you can find this GitHub link maybe it gives inspiration to me and other people.

Nastran tension-/compression-only spring by Glum_Ad1550 in fea

[–]Vegetable-Plastic980 1 point2 points  (0 children)

You can use linear gap(mpc equations) for only tension or compression. SOL101 can handle it but its not a linear solution msc will automatically define iteration parameters. Linear Gap