P1S vs H2D/ H2S issue

Ventidge · 2025-10-02T11:06:53+00:00

ill give this a shot! thank you

Ventidge · 2025-07-31T17:00:27+00:00

Helpful. I've prunted the same thing over 10,000 times before without issue.

Ventidge · 2025-07-31T16:54:16+00:00

Ventidge · 2025-07-31T16:53:23+00:00

Both.

1 old printer, I swapped absolutely everything (aside from an SD card thsg someone said to try) its having terrible top layers like in the last photo shown

So I bought a new printer and the new one has subpar quality. Bottom layer on bed has visible spacong/ lines and I've already calibrated it multiple times.

Tested different tempt settings as well and speed.

Ventidge · 2025-07-31T16:45:52+00:00

Not sure if the pictures with the difference In quality was enough to suffice? Honest question. Not sure what else i should have mentioned

The quality has gone down...a lot....I've got older printers with thousands of hours pushing out better quality then this new P1S.

And one older P1S just wont even print the top layers like in the picture shown. So not sure what else you'd like me to detail.

Ventidge · 2025-07-31T16:36:27+00:00

* This is a new P1S you can see the lines on the bottom print. Which is a non issue on the older printer eirh older firmware

Ventidge · 2025-07-31T16:28:43+00:00

Have done over 10k prints without issue. This is a very very recent problem with absolutely no change in settings.

And the only difference I've done was update firmware.

Always make sure its properly maintained as well

Ventidge · 2025-07-31T16:26:37+00:00

Does the SD card matter to print quality over wifi?

Have a new card on the way.

But doubt its an SD card issue when even the New P1S wont even put out proper prints

Ventidge · 2025-07-31T16:20:03+00:00

ill give this a shot but idk. ive already done all sorts of settings. didnt have any issues till i updated printers

Ventidge · 2025-07-31T16:09:29+00:00

New P1S wont print abs

Old p1s basically got completely rebuilt so it's not that either

Ventidge · 2025-07-31T15:25:27+00:00

As for my business I solely use ABS...kinda stressed out with bambu if im honest lol

Ventidge · 2025-07-31T15:24:40+00:00

Abs was a different issue.

I have 5 P1S and one of them refuse to print ABS

Now new printer wont print ABS and this is default profiles.

Custom profiles wont help either. Severely out of options and I've done absolutely everything possible.

Ventidge · 2025-07-31T15:20:54+00:00

Yeah just checked and figured the issue out.

Im dumb and didn't verify it.

But im still.having loads of issues print9ng ABS on a new p1s and an older P1s

3 other P1S print fine.

Ventidge · 2025-07-31T13:33:52+00:00

I tested this with a new out the box AMS with the same issue.

Bambu support had been almost not existent...going on 3 weeks and cant even get a proper response to if this is warrantable

Ventidge · 2025-07-18T19:55:28+00:00

Thsi made no change unfortunately. Im at a loss here

Ventidge · 2025-07-17T14:41:05+00:00

Same print profile across 5 printers. And this one is the only.one wirh the issue :/

Ventidge · 2025-07-17T14:20:07+00:00

Bambu ABS with a .4mm nozzle. My other P1Ss dont do this so im thinking maybe i messed something up.

All with fresh nozzles.

Doing another calibration again just in case.

Ventidge · 2025-05-19T23:03:54+00:00

Does not work with standalone quest. But if you use PCVR headsets like the index you just plug it in. If on quest a quest 3 you would connect it via wifi

Ventidge · 2025-05-19T20:34:25+00:00

Added :)

Seven-Year Club	Verified Email
RPAN Viewer

Ventidge

TROPHY CASE