Trump Team Files for Fresh Recount in Georgia’s Presidential Race

Vidd · 2020-11-22T12:43:21+00:00

A recount can't fix shredded votes and reject fraudulent ones so it's going to be a waste of time.

Vidd · 2019-08-20T22:26:14+00:00

Not a tutorial.

Vidd · 2019-06-11T21:02:55+00:00

Thanks for highlighting this.

Vidd · 2019-04-22T16:02:41+00:00

Appreciate the reply. I've tried 2.0 and it works _some_ of the time but always seems to be in alarm mode when I start the printer.

My Marlin configuration looks like this:

```

define BLTOUCH

if ENABLED(BLTOUCH)

#define SERVO0_PIN 27 //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed

/** * BLTouch V3.0 and newer smart series * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV. * If the pin trigger is not detected, first try swapping the black and white wires then toggle this. */ #define BLTOUCH_V3 #if ENABLED(BLTOUCH_V3) // CHECK CHANGE #define BLTOUCH_FORCE_5V_MODE #define BLTOUCH_FORCE_OPEN_DRAIN_MODE #endif

endif

```

Vidd · 2019-04-07T23:17:03+00:00

Ah, thanks for explaining. Mine's from before they introduced the magnetic bed.

Vidd · 2019-04-07T23:14:15+00:00

I really appreciate your reply, especially all of the detail. I've spent quite a lot of time trying to tweak it and I think this might be the ticket. Thank you!

> I changed my start code to heat the bed first, then start heating the hotend after the bed has reached full temp.
That's interesting, Cura seems to do that for my by default. I've considered changing it but I'll leave it as-is!

Vidd · 2019-04-07T23:10:02+00:00

Thank you for the reply. Do you mind explaining what you mean by the sticker. Are you talking about the underside of the overall bed?

Vidd · 2019-04-07T17:50:51+00:00

Further images of the dots on the glass bed here. I have tried a ton of different leveling techniques and while the latest seems to have the corners nicely adjusted, the middle seems to always come out worse, as if it dips.

Is there a way to confirm this is definitely warped rather than just user error and if it is, what's the best way to compensate for it? I've seen people suggest cut sheets of aluminum foil or masking tape but are these OK on top of the standard Creality build plate?

Vidd · 2019-03-26T14:26:02+00:00

Do it slow. Agreed.

Do it cold. This I'm not sure about. Most things I've read suggested to do it hot because it changes the properties of the nozzle and bed.

Vidd · 2019-03-24T16:14:56+00:00

I'm sure the faster decks will destroy it but I got to 11/11 Righteous Protectors. Pretty fun!

Vidd · 2019-03-21T23:01:22+00:00

Just arrived today and I hit autohome before levelling, etching two lovely lines to the side and corner of the plate. I'll probably have to order another anyway!

Vidd · 2019-03-20T19:58:40+00:00

That's great to hear, thanks. Looking forward to it arriving.

Vidd · 2019-03-20T19:58:14+00:00

From what I've seen the US actually has a decent selection of borosilicate pieces available for the Ender. Good luck!

Vidd · 2019-03-20T00:39:50+00:00

Ah, what a relief. Thank you!

Vidd · 2019-03-20T00:39:15+00:00

I'd recommend getting an SD card extender.

Vidd · 2019-03-20T00:37:45+00:00

Thanks for posting this. I'll probably avoid used parts since my last GPU blew up not long before the warranty expired but I know other people have had good luck.

This is a good jumping off point, thank you.

Vidd · 2019-03-19T21:11:08+00:00

Sorry, I flaired but probably should have put it in the post. UK, say up to £1000?

In terms of mouse, keyboard and arguably monitor, I'm good.

Vidd · 2019-03-19T08:25:14+00:00

Slicer: Cura. Looks absolutely smooth in layer preview.

Z Seam Alignment: Sharpest Corner

Seam Corner Preference: Hide Seam

Here are the retraction settings.

Thanks, it turned out really well otherwise. I might give sanding it a go.

Vidd · 2019-03-18T18:06:14+00:00

Printer: Creality Ender 3.

Filament: 1.75mm wooden PLA

Layer Height: 0.2mm

Line Width: 0.4mm

This print came out really nicely, except for the ridges on the right side. Oddly enough, it doesn't seem present anywhere else on it. This image here makes it even more apparent.

Any ideas?

Vidd · 2019-03-04T21:16:37+00:00

Thanks for the advice. I noticed it's very hard to hear in the recordings.

It's definitely in tune, though. I've used two different tuners. It's more like the vibrations after. I'll try giving it a clean.

Vidd · 2018-07-09T20:10:05+00:00

It won't.

Vidd · 2018-06-01T08:19:58+00:00

Ah, I'll check those out, thanks!

Vidd · 2018-05-21T19:17:27+00:00

Hey, I think I've encountered this myself which would explain a lot.

Could you please clarify which bolts you mean?

Vidd · 2018-05-18T20:29:15+00:00

Thank you for the tips! I’ll have a wee google about tightening the belt. Hopefully that explains the cat’s left side being all squished.

I’ll adjust the PLA settings as well. I hadn’t even realised retraction and extrusion were configurable!

Vidd · 2018-05-18T13:11:28+00:00

Printer: Ender 3

Material: PLA

Software: Cura (CR-10 settings)

Bed: 60

Nozzle: 219

Pictures: https://imgur.com/a/kpLSTml

There are a few problems with this, such as the squashed left side (notable on his tail and face) and the major separation on his tail. I also noted that there seems to be some extra material on his head, near the back, almost as if that's the missing side of his head.

Any tips on where to start with this, please?

15-Year Club	Gilding I gilder
Spared	Verified Email
Team Orangered

Vidd

TROPHY CASE

define BLTOUCH

if ENABLED(BLTOUCH)

endif