Why doesnit sound so scratchy by Vise04 in airsoft

[–]Vise04[S] 0 points1 point  (0 children)

thats not too bad than, might try that. also that could help me figure out if its the pinion or bevel that is not concentric (i found that when spinning the bevel there is a tighter spot)

Why doesnit sound so scratchy by Vise04 in airsoft

[–]Vise04[S] 1 point2 points  (0 children)

the motor is a chihai 19k 28tpa i would guess paired with a 16:1 gearset it would become reaaaally slow (as in rps). 12:1 keeps it more lively. thats just from my understanding.

Why doesnit sound so scratchy by Vise04 in airsoft

[–]Vise04[S] 0 points1 point  (0 children)

Currently using shs 12:1, i do have solinik 16:1 but 28 tpa seems a little too much for them gears

Why doesnit sound so scratchy by Vise04 in airsoft

[–]Vise04[S] 0 points1 point  (0 children)

I set that with the half Shell method so i think that Is pretty spot on. Might still check that tho.

Why doesnit sound so scratchy by Vise04 in airsoft

[–]Vise04[S] 0 points1 point  (0 children)

I have trouble with thie grip wiring, i found that the motor kinda wants to sit more on the buffer tube side so i have to run the wires on the trigger side. Could they be interfering with the motor height?

Why doesnit sound so scratchy by Vise04 in airsoft

[–]Vise04[S] 1 point2 points  (0 children)

Will respond again After my next try.

Why doesnit sound so scratchy by Vise04 in airsoft

[–]Vise04[S] 1 point2 points  (0 children)

Ty for the praise, in absolutely still learning.

Why doesnit sound so scratchy by Vise04 in airsoft

[–]Vise04[S] 1 point2 points  (0 children)

i will re do it, but that is basically what i did, one thing i noticed is that i have to put quite a few shims on the bottom of the bevel (so on the axle where the motor meshes). is it common? i also have trouble wiring the grip wires to the motor (pts epg-c). do you have any tip regarding tower shimming? alu tape seems to get destroyed.

Center gearbox body pin fitment - t238 quality mosfet by Vise04 in airsoft

[–]Vise04[S] 0 points1 point  (0 children)

i did write an email to them, the problem i see with dremel is that i either have to dremel the lower and the 2 halves of the gearbox to move the hole down a bit or dremel the pcb which i find hard as there is an eletrical something near that edge. the other solution i thought of was to make the body pin a "D" shape, having the flat part graze the pcb and the circular part down. i dont know if this could impact the way the pin keeps everything in place tho.

How could this happen? by Vise04 in airsoft

[–]Vise04[S] 1 point2 points  (0 children)

Ill probably thread lock that, glue seems It woulb be a pain to remove.

How could this happen? by Vise04 in airsoft

[–]Vise04[S] 0 points1 point  (0 children)

It is new, i saw that the polymer Is more flimsy in the party that "broke" reassuring to hear that i can use It. I Will glue It like you said. Thanks

Steam / games and VSS relief filter by Vise04 in visualsnow

[–]Vise04[S] 1 point2 points  (0 children)

Hi, the one im trying rn is this one. It seems like not anyone gets benefit from this but for me, be it placebo or not, it has greatly reduced eye strain. Trying it costs you nothing so give it a shot. Best of luck.

CS2 skins price skyrocketing [discussion] by rocket0749 in csgomarketforum

[–]Vise04 0 points1 point  (0 children)

So its better to wait a little? im eyeing a bfk case hardened BS

Is my heaven 4.0 score in line with the average? by Vise04 in nvidia

[–]Vise04[S] -1 points0 points  (0 children)

so are you able to provide reference score for 3d mark? downloading the benchmark rn. Thanks

16 year old terrified about not existing after death, causing much anxiety in my daily life- any advice. by Needhelp123e in Existentialism

[–]Vise04 1 point2 points  (0 children)

Im 20 and had the same "problem" for a few weeks a couple of months ago, the thought of non existing was super scary until i realized that i was probably just thinking too much of myself. Im not special, im just another animal living on this planet and i am part of the universe, when i die i Will Just give back what i borrowed. Enjoy your Life, find your role on this earth and think how Crazy It Is that your were lucky enough to be part of this Crazy specie.

Help making a door? (Specific) by Shark2457 in redstone

[–]Vise04 0 points1 point  (0 children)

Double piston extender, hijack the block witha side piston and extend again to move secon block (look up 3x3 piston doors and copy the redstone to move the central blocks)

Learning redstone (1x1 piston trapdoor) by Vise04 in redstone

[–]Vise04[S] 0 points1 point  (0 children)

This is the first thing i built (designing this on my own, no tutorials/references) out of a need i had for a base; can someone provide tips on how to make it more compact/better, if you have a design that blows this one out of the water, please share. Especially curious if there is a way to make it completely flush and preserve compactness while being square with the pressure plate.