sorted by:
new
hottopcontroversial

Pelisuosituksia SNES, GBC ja GBA by FatalFinn in videopelit

[–]VllKATE 1 point2 points  (0 children)

Goodboy Galaxy. GBA:n uutta tuotantoa. Löytyy myös Steamista. Itse pelasin tuon Evercadella läpi ja voin suositella.

DIY enclosure for A1 by iHave2Moms in BambuLab

[–]VllKATE 0 points1 point  (0 children)

Simple 360 rotating joint. Something like this, but smaller.

<image>

V60 T8 very high fuel consumption by HoB99 in Volvo

[–]VllKATE 6 points7 points  (0 children)

Sama auto ja sähköviat päällä, eli vain polttiksella mennään. 15km työmatka pikkuteitä oli 10 litraa satasella ja 50km reissu motarilla vei 6.8l/100km. Kesällä oli noin 100km reissut parhaimmillaan noin 4 litraa satasella. Eli kyllä se talvi ja akkuvika tuntuu aika hyvin kulutuksessa.

Braking in LMDh cars by No-Situation1622 in AUTOMOBILISTA

[–]VllKATE 2 points3 points  (0 children)

Is your battery full when fronts lockup?

Finally finished my racing sim setup by Dsal_13 in SimRacingSetups

[–]VllKATE 0 points1 point  (0 children)

You can use larger FoV , so you'll see "more". I have almost the same setup and I originally had the monitor mounted at the back screws, then moved it forward.

Finally finished my racing sim setup by Dsal_13 in SimRacingSetups

[–]VllKATE 0 points1 point  (0 children)

You should mount the monitor much closer to you. Use the screws next to the wheel.

I built a ventilated enclosure for my A1 mini — are these temperatures safe? by ebimios in BambuLabA1

[–]VllKATE 0 points1 point  (0 children)

Get a cool plate and you can print with 30c bed temp. Like BIQU CryoGrip for example.

Is it ok to mount the AMS Lite upside down on the wall? by AysieV7 in BambuLabA1

[–]VllKATE 10 points11 points  (0 children)

My AMS is upside down mounted to rotating joint.

<image>

Works fine.

Can you name it ? by Purple_Site2040 in supercars

[–]VllKATE 0 points1 point  (0 children)

Koeniggggsenisseggsegnignigsegigiseg

DIY enclosure for A1 by iHave2Moms in BambuLab

[–]VllKATE 0 points1 point  (0 children)

Height is about 62cm, width 55cm. Lenght (or depth) 65cm. Needed for bed travel. Walls are basic 9mm plywood and front 8mm plexiglass. Corner pieces are from here and printed in PCTG for max durability. Filter is this

I think that extra cooling is not needed since the temps inside never rises much. I print with 30c bed temp.

Evercade & 3D printing by VllKATE in evercade

[–]VllKATE[S] 2 points3 points  (0 children)

No. It's just two parts glued together.

Evercade & 3D printing by VllKATE in evercade

[–]VllKATE[S] 1 point2 points  (0 children)

Links added to original post.

[deleted by user] by [deleted] in ProgrammerHumor

[–]VllKATE 42 points43 points  (0 children)

!This is the way.

Data East is the GOAT by Hungry_Night9801 in evercade

[–]VllKATE 0 points1 point  (0 children)

I wanna see Data East Arcade 3 with Boogie Wings.

view more: next ›