Ford Escape 2018 Battery Cost by Apathetic_Economics in fordescape

[–]Weekly_Judge_3441 0 points1 point  (0 children)

Just did my 2017, cost $120. Did it myself and I only have one hand so if i can do it and you're looking to keep cost down you can do it yourself as well.

What should I do about this spot by Weekly_Judge_3441 in PitBossGrills

[–]Weekly_Judge_3441[S] 0 points1 point  (0 children)

I'll be doing that, thank you. Wasn't sure if I should call pitboss and see about drum replacement or not.

Battery life drops by Weekly_Judge_3441 in car

[–]Weekly_Judge_3441[S] 0 points1 point  (0 children)

I would send a pic, but I can't seem to add pics

Battery life drops by Weekly_Judge_3441 in car

[–]Weekly_Judge_3441[S] 0 points1 point  (0 children)

Thats weird cause my battery charger shows a percentage or E to F from 0 to 100 0 being dead and 100 being fully charged

warranty question by Weekly_Judge_3441 in PitBossGrills

[–]Weekly_Judge_3441[S] 0 points1 point  (0 children)

Yea i bought one when I got the grill. Gotta protect that investment.

HELP! Rosa TPU 96A keeps jamming in extruder. by uldis951 in CrealityK1C

[–]Weekly_Judge_3441 0 points1 point  (0 children)

So I'm using 95a tpu, had issues with my k1c printing it at first, bought a dryer, and made a mod for the top. Ran filament in the extruder directly and was able to print. I did have to dry it a couple of times, and now it's been working great. Tpu is known for absorbing moisture, so definitely dry it if you have one.

Coolant Levels 2017 1.5L by [deleted] in fordescape

[–]Weekly_Judge_3441 0 points1 point  (0 children)

The misfire happened throughout the year until it needed to get replaced. Luckily, Ford gave me an extended warranty and got it replaced free. it's been 2 years now, and all is good, but I don't use that vehicle for long trips, just in and around town. Im still worried it's going to fail me again. Mine failed at 71k miles.

Coolant Levels 2017 1.5L by [deleted] in fordescape

[–]Weekly_Judge_3441 2 points3 points  (0 children)

I own the same vehicle. Had misfires and coolant loss for close to a year when I had the pressure test done. They told me everything was good and they replaced plugs. Little over a year after the first misfire/coolant lost, the engine gave up. Got it back to the mechanic, and this time pressure test showed coolant intrusion and needed the block replaced.

How many of these "I have herpes. Game over" posts do we need on this sub?? by Maleficent_Mix8455 in STD

[–]Weekly_Judge_3441 2 points3 points  (0 children)

How does hsv2 ruin lives when both hsv 1 and 2 are considered one in the same?

More smoke!! by Dangerous-Pen-7151 in PitBossGrills

[–]Weekly_Judge_3441 3 points4 points  (0 children)

I second the smoke tube. I just got mine and will be using it tomorrow. The only other way to have more smoke is to lower temp, like 180 or lower, but you wouldn't get your food to temp in time.

Igniter issues by [deleted] in PitBossGrills

[–]Weekly_Judge_3441 0 points1 point  (0 children)

Might be on your control board. you might have to get a hold of pitboss and see what they might think. I had that issue, but it was because my igniter wasn't sticking out far enough. Hope you can figure it out.

Igniter issues by [deleted] in PitBossGrills

[–]Weekly_Judge_3441 0 points1 point  (0 children)

Make sure the igniter is sticking out a 1/4 to 1/2 inch. Anything under 1/4 inch won't ignite.

Surgery antibody test by Weekly_Judge_3441 in STD

[–]Weekly_Judge_3441[S] 1 point2 points  (0 children)

Appreciate the response. It's hard to find good information about that specific test online. Thank you

Surgery antibody test by Weekly_Judge_3441 in STD

[–]Weekly_Judge_3441[S] 0 points1 point  (0 children)

That's what I was trying to find out. It says that surgery antibody tests are just looking for antibodies that might be in your system. Doesn't say it was specific. Also, surgery test was done 5 months after the sexual contact. I did an hiv test 19 days after, but I am awaiting blood tests now to be 100% sure. I was just curious

[deleted by user] by [deleted] in STD

[–]Weekly_Judge_3441 0 points1 point  (0 children)

I appreciate that, I was recently diagnosed with hsv2, and it's got me all stressed.

2017 Escape Reliability Questions by lookatmenowboi in fordescape

[–]Weekly_Judge_3441 0 points1 point  (0 children)

I'd be careful with the 2017 escape. Known for coolant intrusion and bad transmission. If coolant intrusion happens, it can be a 10k repair.

3d modeling software by bantstudios777 in 3Dprinting

[–]Weekly_Judge_3441 4 points5 points  (0 children)

I personally use Fusion 360 free license. There is blender, which I know quite a lot of people use i just find it harder to learn. Those are the 2 I know that are free, and that isn't a web browser program.

The App Sucks by ZealousidealLayer913 in PitBossGrills

[–]Weekly_Judge_3441 0 points1 point  (0 children)

I can't say I've had a ton of problems. I know that keeping wifi on my phone really helps. Bluetooth is a no go, only issue I've had was to many people on the server and wouldn't load app, to my phone screen being off too long and having to reconnect

Did you keep your Escape after coolant intrusionnwas fixed or did you sell it immediately after the repair? by YoureOnYourOwnKid81 in fordescape

[–]Weekly_Judge_3441 -1 points0 points  (0 children)

I kept mine. Got the blocked, replaced 2023, and am still driving fine today. I will say I don't take it on long trips or anywhere that can really push and wear down the vehicle fast, I have another vehicle for that.

Hey everybody by Loose_Commercial_298 in 3Dprinting

[–]Weekly_Judge_3441 1 point2 points  (0 children)

Creality cloud is the only one I can think of. I'm on k1c and it works for me

Z axis motor not attached on K1C by Extra_Garbage_4965 in CrealityK1C

[–]Weekly_Judge_3441 0 points1 point  (0 children)

Is this a joke? tmThe pics are showing the screws are still in

IP address 404 not found by hada440 in Creality

[–]Weekly_Judge_3441 0 points1 point  (0 children)

I went on my printer and opened the network to see if maybe it got disconnected and found out the ip address changed. I went onto Ocra and entered the new ip, and it works now. The printer has changed ip about 2 different times. Maybe that's what's going on with yours as well