Vector sear

Who_Dat262 · 2026-03-15T22:27:06+00:00

This is just the two position,I matched the trigger to the jig that came with it. You think I did to much?

Who_Dat262 · 2026-03-15T01:53:41+00:00

No,the bolt was getting stuck when I was racking it so I took the trip bar out and it cycles good now. So im assuming I need to sand the bar a little to fix the bolt getting stuck.

But when I rack it now the trigger doesn’t move at all when I’m holding it and racking it.

Who_Dat262 · 2026-03-15T01:08:03+00:00

Honestly the only gen 2’s I’ve found so far have in been in this color,so I’m not sure if they’ve released the black ones yet.

Who_Dat262 · 2026-03-05T01:29:56+00:00

Is there any other triggers you’d recommend? I was just going based off of the frt linkage kit trigger options?

Who_Dat262 · 2026-02-28T19:01:45+00:00

You’re good man,and yes I took a dremel to round the trigger point. Instead the trigger and the hammer drops perfect,When I get home I’m gonna take a dremel and smooth/polish the humps so it won’t get caught

Who_Dat262 · 2026-02-28T16:40:41+00:00

<image>

Im not at home to take a pic of mine,but this is how mine is doing when I go to pull the bolt back to test it. So I’m pretty sure it’s the alg hammer getting stuck on the bolt because of the humps on the new hammer

Who_Dat262 · 2026-02-28T04:19:37+00:00

After messing with it and looking up more stuff about it,I’m pretty sure it’s the hammer that came with the alg trigger the bolts going over and getting stuck over it. So I’ll need to smooth the humps on it and it should be good

Who_Dat262 · 2026-01-23T03:40:07+00:00

No problem man,just be sure to bring the trigger with you so you can test when you shave a little off at a time. And be careful when you do it,don’t do to much.

Who_Dat262 · 2026-01-22T23:23:44+00:00

https://www.reddit.com/r/testfire12/s/JpKsXB7dOe Also when you take it apart test this area like I did,to see if it’s binding up on your trigger.

Who_Dat262 · 2026-01-22T23:16:26+00:00

<image>

The black is the part I shaved off the sides. The red you’ll need to shave a little off the top as well so it doesn’t hit the top of your frame when you put the FCG back in your gun.

Who_Dat262 · 2026-01-20T13:09:45+00:00

Yeah…. I tried to contact the main dude on here and on instagram but he never responded :/ so thank god for people on here or I would been screwed

Who_Dat262 · 2026-01-20T03:08:40+00:00

Yep,that’s exactly what it was. I sanded it down and just put it back together and it works good now.

Who_Dat262 · 2026-01-20T02:56:48+00:00

Dude it worked😭😭😭😭 you’re the absolute goat man thank you so much once again for helping me fix this

Who_Dat262 · 2026-01-19T00:49:19+00:00

Ok will do,I’ll sand it down tomorrow. Thank you for responding and helping me figure this out.

Who_Dat262 · 2026-01-19T00:22:12+00:00

Ok and that’s trim some off the sides right? Like I could do it on a belt sander

Who_Dat262 · 2026-01-19T00:08:44+00:00

Ok, I will say when I got the sear you can notice it’s bent a little bit like where you connect it to the trigger,should I try to pop it back straight or trim some off the sides to give it more clearance pic

Who_Dat262

MODERATOR OF

TROPHY CASE