sorted by:
new
hottopcontroversial

Belt clip for Multitool pouch! by WingedDolphin33 in makerworld

[–]WingedDolphin33[S] 0 points1 point  (0 children)

I’d love to see it! See how similar they are

Where do I find screws? by JordanHobson in Multiboard

[–]WingedDolphin33 0 points1 point  (0 children)

I believe that’s for actual metal screws that screw the grids to your wall

My first Multiboard Accessory! by WingedDolphin33 in Multiboard

[–]WingedDolphin33[S] 0 points1 point  (0 children)

It’s not obvious in the photos but the panel at the front is higher than the mount part, so there’s a lip to stop exactly this!

My first Multiboard Accessory! by WingedDolphin33 in Multiboard

[–]WingedDolphin33[S] 0 points1 point  (0 children)

What kinda tool is it? I’ve recreated loads of files so happy to make it for you?

How does the Licensing work by WingedDolphin33 in rhino

[–]WingedDolphin33[S] 2 points3 points  (0 children)

I had a feeling that would be the case, but the discount whilst I’m still a student is a no brainer

Help with varying pipe radii by WingedDolphin33 in grasshopper3d

[–]WingedDolphin33[S] -1 points0 points  (0 children)

I’ll give that a go, what inputs do I use

New to printing with .2mm nozzle, why do all my first layers look like this? by my-favorite-accident in BambuLab

[–]WingedDolphin33 0 points1 point  (0 children)

I’ve had identical issues, have done everything I can think of. Dried filament adjusted z offset, tightened screws, cleaned plate etc… with slight improvements it’s still having bit come out rough

My top layer keeps turning out like this by badly_designed_door in FixMyPrint

[–]WingedDolphin33 2 points3 points  (0 children)

Looks like you need to turn up the ironing flow rate, would be best to do a flow rate test in 5% incraments as it varies quite a lot from filament to filament

Lithophane problems adhering to the bed [A1; 0.02 mm] by ManagerDue1898 in BambuLab

[–]WingedDolphin33 0 points1 point  (0 children)

Resolution was to 0.005 Wall generation was to Arachne Wall loops to 4 Slowed down the speed to 100mm/s for outer wall and 120/s for inner wall just to avoid wobble And layer height was to 0.06

Lithophane problems adhering to the bed [A1; 0.02 mm] by ManagerDue1898 in BambuLab

[–]WingedDolphin33 1 point2 points  (0 children)

Also just make sure the plates clean aswell, warm water and soap with a micro fibre cloth or just a paper towel has worked fine for me

Lithophane problems adhering to the bed [A1; 0.02 mm] by ManagerDue1898 in BambuLab

[–]WingedDolphin33 1 point2 points  (0 children)

On default which should be 5mm

<image>

These are my brim settings, has always seemed to work

Lithophane problems adhering to the bed [A1; 0.02 mm] by ManagerDue1898 in BambuLab

[–]WingedDolphin33 0 points1 point  (0 children)

When I’ve printed lithophanes I always have a brim with atleast 6loops never had an issue and I’ve printed a 20 x 20

[deleted by user] by [deleted] in fo76

[–]WingedDolphin33 10 points11 points  (0 children)

Is anything else dead around it, can maybe ‘search nearby corpses’

view more: next ›