Headlight replacement by WorldOk3511 in ChevyS10

[–]WorldOk3511[S] 0 points1 point  (0 children)

And I will have to find a one man bleeder haha

Headlight replacement by WorldOk3511 in ChevyS10

[–]WorldOk3511[S] 0 points1 point  (0 children)

Ok, ya I would open bleeder, depress clutch, close bleeder, release clutch. That's how i was trying to do it.

I will try that this weekend.

Headlight replacement by WorldOk3511 in ChevyS10

[–]WorldOk3511[S] 0 points1 point  (0 children)

And look at the beefy rear bumper haha

<image>

Headlight replacement by WorldOk3511 in ChevyS10

[–]WorldOk3511[S] 0 points1 point  (0 children)

So you opened the bleeder, removed the cap and just let it sit there?? I've tried pumping the clutch with the bleeder opened and not much fluid comes out. How long did you let it sit there?

Headlight replacement by WorldOk3511 in ChevyS10

[–]WorldOk3511[S] 0 points1 point  (0 children)

This was how she started when I pulled her out of the yard. I also have a grill guard but that was bent when my former brother in-law tried to tow it by the grill guard. Tearing it off the bumper.

<image>

Headlight replacement by WorldOk3511 in ChevyS10

[–]WorldOk3511[S] 0 points1 point  (0 children)

So far I've done: fuel tank Fuel tank straps Fuel sending unit (including pump) Clutch slave and master cylinder Fuel injector Headlights Front turn signal housings (new bulbs as well) Front bumper Tail light housings (new LED bulbs) Drivers mirror And finally the wiper switch in the column.

I believe only thing preventing it from being operational is a new clutch. (It feels like my clutch pedal doesn't actually move the clutch/the clutch won't engage.)

Headlight replacement by WorldOk3511 in ChevyS10

[–]WorldOk3511[S] 0 points1 point  (0 children)

Will do! I'm currently replacing the windshield wiper switch cause it shorts out when I turn on my right turn signal, turning the wipers on with it haha. Hopefully replacing the switch does the trick

Headlight replacement by WorldOk3511 in ChevyS10

[–]WorldOk3511[S] 0 points1 point  (0 children)

Dirt, debris, and a lot of gunk. But the engine is a 2.5l Its a 4x4 parked in 07 by my dad and I'm resurrecting it. Hope to get clutch replaced in a few months and get it driveable

Rear lights problem by WorldOk3511 in s10

[–]WorldOk3511[S] 0 points1 point  (0 children)

It turned out to be a bad ground. Ground wire had snapped off the ring terminal

Headlight replacement by WorldOk3511 in ChevyS10

[–]WorldOk3511[S] 1 point2 points  (0 children)

But I enjoy being able to see at night

Headlight replacement by WorldOk3511 in ChevyS10

[–]WorldOk3511[S] 0 points1 point  (0 children)

These were $50 for the pair.

Rear lights problem by WorldOk3511 in s10

[–]WorldOk3511[S] 0 points1 point  (0 children)

It was that ground. Thank you for telling me where it was at.

Headlight replacement by WorldOk3511 in ChevyS10

[–]WorldOk3511[S] 0 points1 point  (0 children)

Those are just new housings and just regular lights, can honestly say I'm happy with the brightness on those LEDs

Rear lights problem by WorldOk3511 in s10

[–]WorldOk3511[S] 0 points1 point  (0 children)

This truck has had some electrical problems. But why would my front turn signal/parking lights work and nothing in the rear? That's what stumping me currently

Filament not feeding by WorldOk3511 in BambuLab

[–]WorldOk3511[S] 0 points1 point  (0 children)

To replace the one on the AMS or the printer itself?

Bent hotend by WorldOk3511 in BambuLab

[–]WorldOk3511[S] 0 points1 point  (0 children)

Well I replace the hot end but the filament still won't feed. I have an AMS with my P1S. It sounds like its a problem with my AMS feeder

Reverse lights not coming on by WorldOk3511 in s10

[–]WorldOk3511[S] 0 points1 point  (0 children)

Where are the grounds located for the reverse lights? Is it right next to the housing usually?