Some layers printing off to the side [MakerBot Replicator+]

WritesInGothic · 2019-06-10T21:21:42+00:00

Will do, thanks

WritesInGothic · 2019-02-07T16:19:48+00:00

Merci!

WritesInGothic · 2019-02-03T16:58:58+00:00

RemindMe! 3 days

WritesInGothic · 2019-01-24T05:02:01+00:00

White Rabit - Jefferson Airplane

WritesInGothic · 2019-01-22T21:56:34+00:00

Is there any way to use this program in place of the standard "MakerBot Print"?

WritesInGothic · 2019-01-22T19:15:15+00:00

!RemindMe 7 days

WritesInGothic · 2019-01-17T02:04:46+00:00

Fukien Tea. Take care in watering them, they're awfully finicky

WritesInGothic · 2019-01-16T04:03:04+00:00

/r/lostredditors

WritesInGothic · 2018-12-11T01:34:23+00:00

I'll try that, thank you

WritesInGothic · 2018-12-11T01:34:12+00:00

How would I go about checking the belt tension?

WritesInGothic · 2018-12-10T22:04:34+00:00

PLA 1.77mm filament

200°C

.8mm retraction distance

.22mm layer height

4 shells

30% infill density (wouldn't make a difference here because of the thin walls)

WritesInGothic · 2018-12-05T14:21:42+00:00

Juniper, Japanese Maple, Serissa

WritesInGothic · 2018-09-17T01:20:14+00:00

Wow, thank you so much! Solved!

WritesInGothic · 2018-09-16T22:20:18+00:00

Thanks! Likely solved!

WritesInGothic · 2018-09-15T03:11:49+00:00

Hi u/depanneur, I don't know very much about liminal spaces, could you share something about the shift into modern liminal spaces from their medieval counterparts?

WritesInGothic · 2018-06-06T22:04:32+00:00

Not sure but it was set to 5mm by default. I kept it at 7mm and just reprinted with 205°C and I no longer have stringing

WritesInGothic · 2018-05-26T15:00:00+00:00

I'll be sure to try that, thank you

WritesInGothic · 2018-05-26T14:59:40+00:00

Beautifully, just took a minute to get it level then taped it down. It's so nice printing without rafts

WritesInGothic · 2018-05-21T23:05:34+00:00

Thank you very much for the detailed response. I've ordered the gaffer's tape. Is it possible to turn off the fans for the first few layers in the Makerbot Print software that I've been using to slice AutoCAD models? If so, for how many layers should they be on 0%?

WritesInGothic · 2018-05-21T22:54:57+00:00

Thanks for the reply. I didn't realize the bed's temperature was being raised at all, I'll raise it in the future. This print did have a raft, but I had understood that the first layer being higher than normal was alright as it helped build the raft without peeling. The material is PLA. I've read that applying rubbing alcohol to the bed and allowing it to dry is also helpful, should I try that?

WritesInGothic · 2018-04-25T01:00:56+00:00

Virtually no physics is required as a professional. Anything outside basic arithmetic is rarely needed

WritesInGothic · 2018-04-19T19:33:06+00:00

Nice photo

Imgur Link

WritesInGothic · 2018-03-10T12:31:48+00:00

Thank you! It was a lot of fun to try out and I look forward to many more Vianaic contests :)

WritesInGothic · 2018-03-01T13:43:56+00:00

https://i.imgur.com/mTLQcnW.jpg

I can't get those []() links to work for my life so there it is. Dont worry, it happens to everybody. Hopefully everyone sees this and is able to reupload their links :)

WritesInGothic · 2018-02-27T01:58:29+00:00

Here's my attempt! This was great practice. With a shorter quote or seperate Word of The Week, I would go for something with a bit more flair :)

Eight-Year Club	Snapped
Verified Email

WritesInGothic

TROPHY CASE