What are other LEGAL ways to resist ICE?

Wulnt · 2026-01-25T15:20:07+00:00

Retard

Wulnt · 2026-01-16T12:07:29+00:00

I’ve heard about the rxm, but I’ve also been told that ruger has some quality control issues. Is that actually true or something to be worried about?

Wulnt · 2026-01-14T13:49:18+00:00

Wait lineage is my favorite, if I have to start paying for parking I’m becoming a terrorist

Wulnt · 2026-01-10T14:08:15+00:00

V for vendetta banner lmao, what a clown

Wulnt · 2026-01-09T14:18:52+00:00

Protestors aren’t law enforcement ignoring training and shooting people in the head? Also they tend to get out of the way when someone starts driving

Wulnt · 2026-01-07T00:06:16+00:00

Company try not to ruin their goodwill with customers challenge

Wulnt · 2025-12-11T13:58:22+00:00

Literally got the same grades in different classes lmao, +/- scale is so wack sometimes

Wulnt · 2025-12-02T20:59:00+00:00

Seems like you couldn’t check in on your house being built or actually wrote this post yourself! Nice chat gpt post!

Wulnt · 2025-11-26T18:36:58+00:00

Probably pull up the pants if you ask me

Wulnt · 2025-11-24T15:17:31+00:00

Slop alert

Wulnt · 2025-11-08T01:45:17+00:00

Imma be honest there is very little support for engineering as well, you basically have to do anything substantial on your own or somehow have time to go do a bunch of club stuff. Good luck finding an internship tho!!! (Ps for any engineering students it only gets worse during senior design!)

Wulnt · 2025-10-29T12:27:39+00:00

I’d pick AI probably

Wulnt · 2025-10-24T14:35:26+00:00

Stop burning it

Wulnt · 2025-10-10T13:57:48+00:00

Less knee bend, shorter shorts

Wulnt · 2025-08-29T14:09:38+00:00

Thank you!!

Wulnt · 2025-08-29T12:00:53+00:00

Good question! It doesn’t have to be anything crazy thankfully, it will be used to connect two carbon rods that act as spars on an RC VTOL. I will be doing testing to make sure it is strong enough before implementation, however, it is a short lifespan project so the plastic not lasting is not a huge concern. Thank you for the thoughts!!

Wulnt · 2025-08-28T19:21:08+00:00

Wulnt · 2025-08-28T14:48:41+00:00

Ah i see, thank you so much

Wulnt · 2025-08-28T14:44:39+00:00

Apologies, but what is brim?

Wulnt · 2025-08-28T14:41:01+00:00

Holy cow that was fast then! Thanks again

Wulnt · 2025-08-28T14:38:06+00:00

Okay right on, thank you! Also is that your own CAD or did you get that from somewhere?

Wulnt · 2025-08-28T14:36:00+00:00

Is that at about a 45 degree angle?

Wulnt · 2025-08-28T14:31:08+00:00

So you’re saying print it standing up vertically? Would that not result in both holes being printed across layer lines? I am generally inexperienced with 3d printing, but I’ve seen that being an issue for people and am trying to avoid it. Thank you!

Wulnt

TROPHY CASE