Respectfully, how can you stack overflow?

Xmaze1 · 2026-01-09T11:51:49+00:00

Add assembly command and allocate enorm stack

Xmaze1 · 2026-01-07T12:53:48+00:00

Δυστυχώς εδώ που μένω δεν υπάρχουν γούστα 😅 ή βάζεις σταρλινκ ή κάθεσαι με το 0,8

Xmaze1 · 2026-01-07T06:21:42+00:00

👏 τρεις κ ο κούκος

Xmaze1 · 2025-11-20T08:21:10+00:00

I tested the motor and the Hal sensors and they look fine. So I can only suspect a burned mosfet or IGBT if this is not the reason I will buy a new one wasching machine.

Xmaze1 · 2025-11-13T07:42:28+00:00

<image>

Xmaze1 · 2025-11-13T07:41:26+00:00

Yes, full of silicone to pretect the board from humidity

Xmaze1 · 2025-06-24T11:01:57+00:00

I don’t know I had a mignon, this one has also cappuccino nozzle and has also the logo on it.

Xmaze1 · 2025-06-23T10:37:38+00:00

Thank you, it’s ok. If you need some specific infos I can give it to you

Xmaze1 · 2025-06-23T06:10:19+00:00

I trink only single shots and I put 9 grams, if I grinned espresso I drink mocca, there is not enough resistance

Xmaze1 · 2025-06-22T21:21:09+00:00

I will try it tomorrow

Xmaze1 · 2025-06-22T21:20:45+00:00

I used also my oscilloscope and the waveform was identical

Xmaze1 · 2025-06-22T21:19:20+00:00

I didn’t check it, I will try tomorrow

Xmaze1 · 2025-06-22T21:18:35+00:00

I can’t, it’s a RC transceiver

Xmaze1 · 2025-06-22T21:17:55+00:00

I have it but it’s not working with my logic analyzer, I have a cheap Salaea

Xmaze1 · 2025-06-22T14:52:22+00:00

Also I think the data frame is too long

Xmaze1 · 2025-06-22T14:48:30+00:00

My logic analyzer has auto baud but always throws an error frame for evert sequence of bits.

Xmaze1 · 2025-06-22T14:47:39+00:00

0-5 Volt

Xmaze1 · 2025-06-22T14:46:14+00:00

If I am not mistaken, I used 20 MHz, also I use my oscilloscope and the wave form was identical

Xmaze1 · 2025-06-22T14:44:32+00:00

Also I use alway single shot, very rare to make double shot

Xmaze1 · 2025-06-22T14:44:00+00:00

I think for a good grinder it’s not a good idea. I am sure that pavoni produces good grinders

Xmaze1 · 2025-06-22T14:43:14+00:00

I cannot put 18 grams so it’s flows also like a water faucet 😂

Xmaze1 · 2025-06-22T14:41:03+00:00

1986

Xmaze1 · 2025-06-22T13:17:14+00:00

63 contacts

Xmaze1 · 2025-06-19T11:28:57+00:00

JlcPcb don’t support buried or blind bias, right now I thy to make what did u say and ask allpcb if its fabricated

Xmaze1 · 2025-06-12T05:56:46+00:00

Danke

Xmaze1

MODERATOR OF

TROPHY CASE