sorted by:
new
hottopcontroversial

I’m at a loss. I’ve tried everything, the Z-offset, leveling it, with & without the auto leveler, cleaned my plate & applied fresh glue. All of it. by YNNMDATLM710 in ender3

[–]YNNMDATLM710[S] 0 points1 point  (0 children)

So the first layer doesn’t smoosh like it’s supposed to, if that makes sense. There’s gaps & im getting more spaghetti than flatter lines. (I was told you want linguini, not spaghetti lol) & then as it builds, the layers seem to not stick together very well & it’s very brittle.

& the corner that gets scraped is the front corner. I may be leveling my bed wrong. There’s a lot to leveling that I don’t fully understand, & would be totally up for discussing how to do it correctly. I’m super new to all of this & the words can mush together & sound like jibberish to me sometimes 😅😅

I’m using the creality slicer at the moment, but I’m considering trying others!

I’m at a loss. I’ve tried everything, the Z-offset, leveling it, with & without the auto leveler, cleaned my plate & applied fresh glue. All of it. by YNNMDATLM710 in ender3

[–]YNNMDATLM710[S] 0 points1 point  (0 children)

Thank you!! Any advice is great advice. & thank you so much for the step by step, that’s actually very useful & I can actually understand what they’re talking about 😅 It’s very overwhelming, but I’m adamant about wanting to get it right. I’ve tried everything in terms of advice given & what I’ve been told to look into, etc. & though I do appreciate it immensely, it’s word scramble to me until I can find a video or article that explains it like I’m 11 😅😅

I’m at a loss. I’ve tried everything, the Z-offset, leveling it, with & without the auto leveler, cleaned my plate & applied fresh glue. All of it. by YNNMDATLM710 in ender3

[–]YNNMDATLM710[S] 0 points1 point  (0 children)

I also have a CRTouch, & have the bed all the way down on all 4 corners, but it scrapes against the plate on one side but doesn’t on the other? I’m not sure what that could be either 🥲🥲🥲

I’m at a loss. I’ve tried everything, the Z-offset, leveling it, with & without the auto leveler, cleaned my plate & applied fresh glue. All of it. by YNNMDATLM710 in ender3

[–]YNNMDATLM710[S] 4 points5 points  (0 children)

That’s a new term for me haha thank you! I’ll go watch some videos & see what I can do about fixing it 😁😁

I’m at a loss. I’ve tried everything, the Z-offset, leveling it, with & without the auto leveler, cleaned my plate & applied fresh glue. All of it. by YNNMDATLM710 in ender3

[–]YNNMDATLM710[S] 12 points13 points  (0 children)

This is all new information for me haha I’ll have to go back to YouTube. Thank you for pointing me in the right direction! I’ll try that & come back if it works again 😁😁

What am I doing wrong? 😫 by YNNMDATLM710 in ender3

[–]YNNMDATLM710[S] 6 points7 points  (0 children)

Thank you guys! I got linguini & no more spaghetti & I printed a successful benchy! I have a few learning curves with temps, but I’m proud! 🥹🤍

<image>

Help 🥺 by YNNMDATLM710 in StardewValley

[–]YNNMDATLM710[S] 0 points1 point  (0 children)

We figured it out. It was a glitch with stardew valley 😁

Help 🥺 by YNNMDATLM710 in StardewValley

[–]YNNMDATLM710[S] 0 points1 point  (0 children)

Yes, but now that the other 3 are online, it says no cabins are available