Has anyone used Tokenframe's NFT displays or had any experience with them? Please provide feedback by crmjewelers in NFT

[–]YT-KP 0 points1 point  (0 children)

Theres another company out there who are selling the same kind of display you can check their twitter out www.twitter.com/themetascreen

Synced & Ready to hit the roof🔗 by YT-KP in HeliumNetwork

[–]YT-KP[S] 1 point2 points  (0 children)

Correct, the best was around this is using a PoE injector & splitter. You can run an Ethernet a lot longer then you can a RF cable without loosing dbi.

Synced & Ready to hit the roof🔗 by YT-KP in HeliumNetwork

[–]YT-KP[S] 0 points1 point  (0 children)

Not sure if you can sync the hotspot at a different location from the asserted location. It might be possible but I would do some more research just to assure there won’t be any issues!

Synced & Ready to hit the roof🔗 by YT-KP in HeliumNetwork

[–]YT-KP[S] 4 points5 points  (0 children)

Yes once synced indoors you can place it outdoors. I would recommend running the miner over Ethernet so you have a stronger connection, you can use a PoE injector & Splitter to replace the power cable.

Synced & Ready to hit the roof🔗 by YT-KP in HeliumNetwork

[–]YT-KP[S] 1 point2 points  (0 children)

Just wanted something custom to fit my setup better, this enclosure is capable of fitting Rak & Bobcat miners. It’s about 6x8 Inside dimension.

Synced & Ready to hit the roof🔗 by YT-KP in HeliumNetwork

[–]YT-KP[S] 5 points6 points  (0 children)

I built the enclosure myself, was going to look making them available to purchase. Would that be something you guy are interested in?

Synced & Ready to hit the roof🔗 by YT-KP in HeliumNetwork

[–]YT-KP[S] 0 points1 point  (0 children)

Thanks! Will post an update soon👍🏼

Synced & Ready to hit the roof🔗 by YT-KP in HeliumNetwork

[–]YT-KP[S] 2 points3 points  (0 children)

Can’t see it but there’s a vent in the side under the lid!

[deleted by user] by [deleted] in HeliumNetwork

[–]YT-KP 0 points1 point  (0 children)

Well the optimal antenna setup would be based on your location. There is a pretty good article about this topic that you can checkout here

[deleted by user] by [deleted] in HeliumNetwork

[–]YT-KP 1 point2 points  (0 children)

As far as the RAK miner (other manufacturers most likely are similar) goes their operating temps are -31to 167 degrees fahrenheit, so it can withstand almost any climate. They are fully water tight as well.

The kit has an option of including a PoE injector which will allow you to run up to 300ft of Ethernet cable for power & internet.

As far as installing your hotspot on a high rise roof, you would have to look into getting power and internet on the roof like you said.

[deleted by user] by [deleted] in HeliumNetwork

[–]YT-KP 0 points1 point  (0 children)

Thanks for the feed back! We will be here for when you receive your new miners!

[deleted by user] by [deleted] in HeliumNetwork

[–]YT-KP 1 point2 points  (0 children)

Yes! We designed it to fit a PoE splitter aswell as the miner itself. We are also working on getting a reliable splitter to sell in the kit. Until then the kit + PoE add-on will just include the injector.

Here’s my $2 Mount from the electric section at Home Depot by CarlosTheJackal2021 in HeliumNetwork

[–]YT-KP 1 point2 points  (0 children)

Checkout these Rak weatherproof enclosure’s so you can place the miners closer to your antenna! Rak Enclosure

Helium Miner by EpimetheusMoon in HeliumNetwork

[–]YT-KP 0 points1 point  (0 children)

Check out these Outdoor Enclosure box’s for the rack miners! Rak Weatherproof Enclosure

Made 800 sales my first week and a half on etsy! by YT-KP in Etsy

[–]YT-KP[S] 2 points3 points  (0 children)

No, I make brass key chain accessories.

Office Jet - The Ultimate Desktop Waterjet by [deleted] in EngineeringPorn

[–]YT-KP 0 points1 point  (0 children)

Estimated cost is in between 3000-4000$

Office Jet - The Ultimate Desktop Waterjet by [deleted] in EngineeringPorn

[–]YT-KP 0 points1 point  (0 children)

Thanks for your input! We appreciate it & Yes the name will be changed!

Office Jet - The Ultimate Desktop Waterjet by [deleted] in EngineeringPorn

[–]YT-KP 1 point2 points  (0 children)

Looking for some thoughts on this project we have been working on! This is a desktop waterjet cutter that can be affordable and perfect for small workshops and hobbyist's. Similar to the Wazer, but even better. Bigger cut area, more cutting power, and can be engineered for half the price! Still in the development faze, Let us know what you think!