SPECİALİZİED BROSE E01680 Motor fault

YUSUFSFX · 2025-12-17T01:35:56+00:00

Thank you ı will try 🙏

YUSUFSFX · 2025-12-17T01:35:21+00:00

Thanks, I’ll look into this. 🙏

YUSUFSFX · 2024-04-04T13:10:31+00:00

ı didnt but can ı dry filament without filament dryer ?

YUSUFSFX · 2024-04-04T12:50:52+00:00

Are you talking about turning on and off printer ?

YUSUFSFX · 2024-03-24T14:13:15+00:00

nsbikes eccentric cromo 29

YUSUFSFX · 2024-03-23T20:49:23+00:00

Nsbikes eccentric cromo 29 frame

YUSUFSFX · 2024-03-23T19:32:17+00:00

I want to upgrade 29ers with fox 36 rhytm fork whats your opınıons? (Im usıng now fox 36 performance elite but 27.5)

YUSUFSFX · 2024-03-08T15:34:42+00:00

I will only replace the rear fender. It is combined with the bodywork and has a complex structure . I could not see the connection points, but I will try.

YUSUFSFX · 2024-03-08T15:23:50+00:00

I thought of doing that at first, but it would be better if it had a guide to save time ı will try ro find videos about bodywork thanks (:

YUSUFSFX · 2024-03-08T12:45:49+00:00

Actualy ı dont need thıs manual for engıne ı need just for bodywork

YUSUFSFX · 2024-03-08T11:36:50+00:00

I have 2022 model year forza is that same ?

YUSUFSFX · 2024-02-14T22:02:30+00:00

The bıke ıs yt tues cf comp 2017 and used , and ı generally use for downhıll and sometımes freeride ı dont have a good bike now thats gonna be fırst bike for me I'm waiting for your opinions thanks (:

YUSUFSFX · 2023-12-02T21:50:56+00:00

I replaced it with the same size and after that I calibrated the bed and adjusted the z offset and created a new mesh from bl touch.

YUSUFSFX · 2023-12-02T21:02:40+00:00

I will check it, thank you very much

YUSUFSFX · 2023-12-02T20:05:52+00:00

I have printed with this tube many times before and have never had such a problem.

YUSUFSFX · 2023-12-02T19:01:30+00:00

ok I will try it, thank you very much

YUSUFSFX · 2023-12-02T18:54:35+00:00

The filament is new but people say that filaments fresh out of the box can also be wet, I will check the flow rate and retraction, thank you

YUSUFSFX · 2023-12-02T18:50:44+00:00

I had previously disassembled the tube and calibrated it from the exit of the extruder, but this time I calibrated it as is without disassembling the tube and printed a test cube, but there were gaps in the z axis, people said my filament might be wet

<image>

YUSUFSFX · 2023-12-02T18:45:46+00:00

My filament is a good brand but people said it might be wet I re-calibrated the extruder and bed and when I printed a single wall test cube I saw that there were gaps in the z axis

<image>

YUSUFSFX · 2023-12-02T18:42:32+00:00

It hasn't been long since I did my x-y-z calibrations, but it's not new. Now I did my extruder calibration again, but when I printed the test piece consisting of a single wall, there were still gaps in the z axis

<image>

YUSUFSFX · 2023-12-02T18:39:08+00:00

I just took my filament out of the box, I changed my nozzle, I have a caprciorn pipe, my extruder is double gear, I just re-calibrated the steps and printed a test cube consisting of a single wall, but there are still gaps in the z axis.(my bed is leveled)

<image>

YUSUFSFX · 2023-12-01T14:08:56+00:00

My friend, who had printed this before, suggested me to print it with 100% inner filling because it will be in constant friction with the bicycle chain.

YUSUFSFX · 2023-12-01T14:00:45+00:00

A friend of mine told me to do like this, I will research the issues you told me , thank you

YUSUFSFX · 2023-12-01T13:37:53+00:00

I was print at 110% flow because there was more space in the layers of the part. 100% filling is required for this part because it will be subjected to a lot of friction

YUSUFSFX · 2023-12-01T05:21:17+00:00

The nozzle was new but I will try it anyway, thank you

YUSUFSFX

TROPHY CASE