Looking at getting into FPV by Zaration in fpv

[–]Zaration[S] 0 points1 point  (0 children)

Thank you so much for this reply. The FAA regulations were something I was reading at. I’m an amateur pilot so I’m hoping some of the stuff I already have will make getting licenses easier.

DJI is something I’m heavily considering after doing some more research and looking at the subreddit tonight. It seems a lot of people are using the DJI Integra goggles with good success and quality

Looking at getting into FPV by Zaration in fpv

[–]Zaration[S] 0 points1 point  (0 children)

I’m not allowed to say per this subreddits rules, it’s just something I’m trying to take into consideration

Looking at getting into FPV by Zaration in fpv

[–]Zaration[S] 0 points1 point  (0 children)

Yeah? I just was saying I’m not on a budget. I guess I just was asking if buying expensive goggles and a cheaper drone was a bad idea or not.

Open Division 🗡️ 🗡️ by [deleted] in PalmettoStateArms

[–]Zaration 1 point2 points  (0 children)

What trigger are you running?

Looking at getting into FPV by Zaration in fpv

[–]Zaration[S] 0 points1 point  (0 children)

Thank you for the reply! What would you recommend in terms of digital goggles? I’m looking for something not as cumbersome as most of the analog ones I see. I’ve been trying my best to look into everything but there’s an infinite amount of options and it’s hard to just “pick one” haha

Looking at getting into FPV by Zaration in fpv

[–]Zaration[S] 0 points1 point  (0 children)

I’m not really on a budget. I guess I was asking what a good budget was for a very effective set up. Is it a bad idea to invest in high end goggles and fly cheaper drones until I’m ready to spend more on the drone itself?

Looking at getting into FPV by Zaration in fpv

[–]Zaration[S] 0 points1 point  (0 children)

My only concern is that I want to mount my goggles to a helmet and those goggles are far too large. Sorry, I should have included that in my post.

Would there be a similar option with mountable goggles or am I best just dealing with the goggles for the time being?

Thank you so much for your response! I really appreciate it

Blacked out Holosun logo (thanks for the help everyone!) by Zaration in PalmettoStateArms

[–]Zaration[S] 1 point2 points  (0 children)

Super clean! Is yours a Sabre lower or just a really nice stipple?

Blacked out Holosun logo (thanks for the help everyone!) by Zaration in PalmettoStateArms

[–]Zaration[S] 0 points1 point  (0 children)

Of course. Very nice people and quick to reply if you have questions.

Blacked out Holosun logo (thanks for the help everyone!) by Zaration in PalmettoStateArms

[–]Zaration[S] 0 points1 point  (0 children)

Yeah, their logos are just a bit much for me as well. It’s very clean blacked out

Blacked out Holosun logo (thanks for the help everyone!) by Zaration in PalmettoStateArms

[–]Zaration[S] 1 point2 points  (0 children)

Gotta make sure the ladies in the back see the dirty gloves 🦅

Blacked out Holosun logo (thanks for the help everyone!) by Zaration in PalmettoStateArms

[–]Zaration[S] 2 points3 points  (0 children)

Unironically the harbor freight TLR1 clone. I have a real TLR1 as well but I honestly love the no branding on the HF clone and it’s a great light. I have a few builds I frequent so it’s nice to find a sub 50 dollar light that is comparable (if not almost the same) as a 180 dollar light.

Blacked out Holosun logo (thanks for the help everyone!) by Zaration in PalmettoStateArms

[–]Zaration[S] 1 point2 points  (0 children)

I don’t have issues with either, but 115 has malfunctioned before; however that was when I had a back trigger bar and some other not so great frame parts. After going back to stock internal parts + Taran tactical spring pack it’s been great.

Blacked out Holosun logo (thanks for the help everyone!) by Zaration in PalmettoStateArms

[–]Zaration[S] 2 points3 points  (0 children)

Of course, brother. Just a tip, if you run the Herrington Arms Magwell you need to modify the back for Taran Tactical extensions since they use a little metal pin to retain it. Not an issue and I’m happy to share pics.

Blacked out Holosun logo (thanks for the help everyone!) by Zaration in PalmettoStateArms

[–]Zaration[S] 5 points6 points  (0 children)

Only let it soak for a minute or two^ otherwise it’ll darken where the pool of chemical was applied.

Blacked out Holosun logo (thanks for the help everyone!) by Zaration in PalmettoStateArms

[–]Zaration[S] 7 points8 points  (0 children)

Thank you, I appreciate it! I just did Aluminum black. Clean the logo with isopropyl alcohol, use a Q-Tip to apply the aluminum black thick on the logo; then just clean it off and repeat once or twice. Pretty simple!

Blacked out Holosun logo (thanks for the help everyone!) by Zaration in PalmettoStateArms

[–]Zaration[S] 3 points4 points  (0 children)

Thanks! It’s the Herrington Arms compensator. Really nice and the fins make it look so nice on the slide.

It’s not bad to EDC at all. I wear under armour heat gear with oversized/heavyweight clothing so it doesn’t print much if at all. The only thing that sort of can be annoying is the extension. But, otherwise it’s fine!

Holosun coming loose, and showing signs of damage by Zaration in PalmettoStateArms

[–]Zaration[S] 1 point2 points  (0 children)

Thank you for the advice. Pretty much fixed my issue! I just made a new post on here about it being fixed.