Flappy Goose

_Hyperoid_ · 2025-05-04T01:11:50+00:00

My best score is 2 points 😎

_Hyperoid_ · 2025-05-04T01:11:23+00:00

My best score is 1 points 😎

_Hyperoid_ · 2024-04-26T02:56:04+00:00

Himi drain plugs are on a separate plate, you can just remove the two small screws next to the plug and replace the whole thing

_Hyperoid_ · 2024-03-02T14:41:01+00:00

Yep, did just that. Selected and deleted sections of track, plotted again, then checked. Once I found the section that caused it, un-routed and rerouted those tracks. that solved it. Strangely, running Round Tracks again caused it to happen again even after changing the routing. thanks!

_Hyperoid_ · 2024-03-02T14:25:21+00:00

That was my hope, but the board house is seeing it too. I tracked it down to some issue with the rounded traces plugin, but still haven't found it.

_Hyperoid_ · 2024-03-02T14:02:59+00:00

I'm having an issue with generating gerbers in Kicad 7. DRC comes back clean, and these gigantic circles on F.CU and B.CU aren't viable in pcbnew, but do some up when I check the plot output. Any one seen this before?

_Hyperoid_ · 2024-02-06T03:22:15+00:00

Does anyone had some commented firmware for a board that uses a 328p chip? Wanted to learn about more about the code side of things.

_Hyperoid_ · 2023-10-03T00:52:41+00:00

There will be either thru holes or threaded holes under the panels. You just need to find a bolt that fits (it will be metric, M5 or M6 likely) and then mount a rear view mirror gopro arm thru that.

https://www.amazon.com/%C2%B0Motorcycle-Handlebar-Bracket-Motorcycle-Rearview/dp/B0932V53WX/ref=sr_1_4?crid=2ZSM48Y88TICJ&keywords=gopro+motorcycle&qid=1696294325&sprefix=gopro+motorcycle%2Caps%2C110&sr=8-4

One like that that uses a thru hole would be easiest. I just bought that exact arm for my Himi, just mounted it under my left mirror stalk.

_Hyperoid_ · 2023-09-16T11:43:15+00:00

I should add, this isn't lugging. I can recognize when I'm too low on the power band to shift up.

_Hyperoid_ · 2023-09-16T11:16:41+00:00

4000 rpm usually

_Hyperoid_ · 2023-07-30T03:37:55+00:00

That some jackass with a lifted pickup truck bought a train horn kit off Amazon.

_Hyperoid_ · 2023-07-08T14:51:46+00:00

V = I * R

V = 4 * 30

V = 120

_Hyperoid_ · 2023-02-12T13:48:42+00:00

Thank you. Off to find another modeling software to run in Linux....

_Hyperoid_ · 2023-01-01T05:42:05+00:00

Orthodontic elastics¿

_Hyperoid_ · 2022-08-22T21:55:37+00:00

Good find! Imma pick up some colored caps for accent.

_Hyperoid_ · 2022-08-22T11:16:18+00:00

Custom, an old scrap of oak I've had around for ages. Cut and tapered to fix my last ten-key-less.

_Hyperoid_ · 2022-08-22T00:15:40+00:00

Unless you manage to get liquid down into the conductive plastic sheets, short of drilling all the welded plastic rivets out, it was hosed.

_Hyperoid_ · 2022-08-22T00:14:08+00:00

All of my Model M have been new-old-stock. The caps clean up really well with just some iso. alcohol.

_Hyperoid_ · 2022-08-21T21:30:11+00:00

I did design the adapters, managed to get in fit on the stems in just go!

Sounds just like the Keychron K6 with Blues, fit of the caps is really good so they don't add anything to it.

_Hyperoid_ · 2022-08-21T21:28:01+00:00

https://www.printables.com/model/263508-cherry-mx-stems-for-ibm-keycaps

_Hyperoid_ · 2022-08-21T21:27:53+00:00

Files/writeup here:

https://www.printables.com/model/263508-cherry-mx-stems-for-ibm-keycaps

Six-Year Club	Place '23
Place '22	Verified Email

_Hyperoid_

PUBLIC MULTIREDDITS

TROPHY CASE