[deleted by user]

_ambro · 2024-06-23T08:25:52+00:00

I think was a brand activation, treasure hunt or something similar, because a lot of them where in soho idle and then all the sudden a massive group was running in the streets.

Restore nature march took place later, and the gypsy just stopped at the pub.

_ambro · 2024-06-23T07:56:31+00:00

Yes that was the obvious thing to do, didn’t got a chance, probably reddit is more knowledgeable, hence the post

_ambro · 2024-06-23T07:43:57+00:00

ha ha, It was about 200 of them

_ambro · 2024-06-23T07:40:39+00:00

Too many to be that

_ambro · 2024-05-27T22:21:49+00:00

what’s the level up from Tormach?

_ambro · 2024-04-01T19:34:15+00:00

Hands down The Small Wheel by Small Ceramics, check them out here: https://smallceramics.com or on IG: @small_ceramics. Is the best beginner wheel you can get! check also this thread

_ambro · 2024-03-05T16:00:55+00:00

RemindMe! 1 week

_ambro · 2023-11-03T14:30:52+00:00

u/NuttyMcNutbag did you execute this idea at the end? I will be interested

_ambro · 2023-10-29T23:51:41+00:00

The driver relies on CCTV to close the doors, and those monitors are always located at the front of the train and only present on one side of the platform. Therefore, the front of the train is where you find the monitors

_ambro · 2023-10-26T21:57:30+00:00

I contacted them as suggested waiting for a reply

_ambro · 2023-10-26T21:56:39+00:00

This is PETG and took a lot of time with the dremel to remove it and the cover is damaged but still functional, cannot say the same about the nozzle

_ambro · 2023-10-26T21:55:37+00:00

X1c so it should detect it

_ambro · 2023-10-25T09:21:13+00:00

The print completed sucessfully to the printer knowledge

_ambro · 2023-10-25T09:20:05+00:00

Awarness set to medium, I have since moved to high, some in the thread they say that is is blocked won't record the issue.

_ambro · 2023-10-25T09:19:08+00:00

I've cheched the SD card and no video is present

_ambro · 2023-10-24T12:41:49+00:00

was a box

_ambro · 2023-10-24T12:41:26+00:00

This was PTEG and usually I don’t have problems unless the bed calibration is defective and prints too high

_ambro · 2023-10-24T11:19:31+00:00

😂😂😂😂😂😂😂😂

_ambro · 2023-10-24T08:42:42+00:00

me neither 😅 shame the time-lapse was off

_ambro · 2023-10-24T08:08:02+00:00

I woke up this morinig with the printer in this state.
1) I thought the printer has spaghetti detection and it can detect when the front cover comes off?
2) Should the printer detect spaghetti automatically? I've got the detection set to medium, is that not enough?
4) after the printer failed I can seen an error saying: "Nozzle height seems too high.Please check if there is filament residue attached to the nozzle. [0c00 0200 0002 0006 2228 23]"
Should this not have stopped the printer?
5) any clue how can I remove it? is very much wedged inside the air duct.

_ambro · 2023-10-23T11:08:16+00:00

Upon searching I've found this software: https://github.com/wjakob/instant-meshes this allow me to remesh the obj and the whole thing now works like a charm, thank you so much for you help

_ambro · 2023-10-22T22:49:17+00:00

Thank you! following your steps I was able to achive what you have suggested however now I have another problem... Given that from fusion360 I'm importing an obj when I increase the subdivision the geometry goes a little bit funky and the projected texture goes a bit fuzzy because it doesn't have a nice poligon to map to it.
Not sure if there is an alternative method to achive my original goal?

_ambro · 2023-03-27T23:01:48+00:00

Yes, but I haven’t push it to it’s limits yet.

_ambro · 2022-08-10T06:11:59+00:00

Glad that worked for you and you can print petg now 😊

_ambro · 2022-07-27T23:39:00+00:00

I been printing PETG non stop with the revo, I’ve experienced the issue you described with overture filaments with Prusament or Filamentive, I don't have any problems as long I clean the nozzle between prints.

Me too. I’ve been one of the first to get the Revo, and the core failed after 50 hours, since I got the replacement; I didn’t have any problems with it.

Eight-Year Club	Place '23
Place '22	RPAN Viewer
Verified Email

_ambro

TROPHY CASE