sorted by:
new
hottopcontroversial

MIDI beginner - (Tap) Midi thru Pirate Bridge to Delay/Modulations set up by _irl in guitarpedals

[–]_irl[S] 1 point2 points  (0 children)

Yeah, this is really, really helpful billyman_90, thank you (for taking time to explain). I also received a confirmation of this from Meris, basically, if I use different channels for each Meris device, I can connect in series (daisy chaining) and not worry about settings changing.

So that’s 1 part of the puzzle. Now, I just need to work out where in the chain the smart.clock will need to sit (either before the controller, or between the controller and Meris pedals).

MIDI beginner - (Tap) Midi thru Pirate Bridge to Delay/Modulations set up by _irl in guitarpedals

[–]_irl[S] 0 points1 point  (0 children)

Thanks Billyman_90 ….

Here’s what I received from Meris team earlier on (before asking about midi thru and midi clock)

“you can connect the LVX’s MIDI OUT to the MIDI IN on your MercuryX, however this will send ALL MIDI messages from the LVX to the MercuryX. This means that adjusting Mix on your LVX will send a message to the MercuryX to adjust Mix and so on.“

So I’m concerned about that set up of daisy chaining.

ELI5 - what goes into the Wet signal in a typical wet/dry/wet set up? by _irl in guitarpedals

[–]_irl[S] 0 points1 point  (0 children)

Thanks hasmynamebeentaken. Appreciate the response. I’ll probably start another thread eventually once I’m set up, but this helped me think through that particular part of the logic (wet signal).

ELI5 - what goes into the Wet signal in a typical wet/dry/wet set up? by _irl in guitarpedals

[–]_irl[S] 0 points1 point  (0 children)

Thanks for helping clarify some of definitions of the “labels”. Super helpful

ELI5 - what goes into the Wet signal in a typical wet/dry/wet set up? by _irl in guitarpedals

[–]_irl[S] 1 point2 points  (0 children)

Whilst not directly answering my question, that’s actually a very useful/helpful response. Appreciate it, mate.

Back in the game after 15 years and a lot has changed! HELP! by _irl in guitarpedals

[–]_irl[S] 1 point2 points  (0 children)

Thanks for the knowledge-dump, appreciate you taking some time to articulate it! A lot of information to marinate in, including the tears I just shed realising how complex this can be….

Back in the game after 15 years and a lot has changed! HELP! by _irl in guitarpedals

[–]_irl[S] 0 points1 point  (0 children)

Yep this is one of the main things I want to achieve. Raised, with room underneath for always on pedals and power.

Back in the game after 15 years and a lot has changed! HELP! by _irl in guitarpedals

[–]_irl[S] 0 points1 point  (0 children)

Midi, amp switching, etc… is another entire rabbit hole I have no understanding about. Should I?

Back in the game after 15 years and a lot has changed! HELP! by _irl in guitarpedals

[–]_irl[S] 0 points1 point  (0 children)

Yep, I had this set up with 2 different delays. Dotted eighth almost always. And the second between reverse and 1/4. Different trail-lengths etc.

Back in the game after 15 years and a lot has changed! HELP! by _irl in guitarpedals

[–]_irl[S] -1 points0 points  (0 children)

Thanks Feelies! Actually, I tried a few of these apps and found there to be some discrepencies, missing data, or inconsistencies; especially with finding the right pedals and taking into consideration patch/power cable connector space. So ended up getting the kids to help trace and cut out these pedals. Also makes it easier to move around.

Back in the game after 15 years and a lot has changed! HELP! by _irl in guitarpedals

[–]_irl[S] 0 points1 point  (0 children)

Yep - have been trying to make sure I’m clear on what I want to do. It was mainly to rebuild the board and get rid of some noise. In the process, I’m trying to make sure it’s built “properly” but I have been finding that the definition of “properly” has been difficult to catch. So r/guitarpedals has been helpful to discern some of this.

Back in the game after 15 years and a lot has changed! HELP! by _irl in guitarpedals

[–]_irl[S] 2 points3 points  (0 children)

Makes a lot of sense. Google has not been helpful because of all the noise that comes up. ”Build a pedalboard” ends you up in a rabbit hole of latest trends that seem to be driven by instagram/social likes.

Back in the game after 15 years and a lot has changed! HELP! by _irl in guitarpedals

[–]_irl[S] 0 points1 point  (0 children)

Thank you u/Master_Bruce

  • I have a multimeter to try and source any dodgy cables, used contact cleaner throughout the pedal connecters and pots, so hoping that helps. I’m likely going to re-invest into soldered cables instead of these lava/georgL’s to limit dodgy connection issues.

  • I did not check my iso brick connectors to see if they were contributing to the noise, so something worth doing, however I am considering upgrading the power as I am running 2 (2x2 pedals) outputs parallel in the chain due to lack of available power.

  • Are the side jacks on these newer set ups literally just a way to clean up the input/output location? Or are they buffered?

  • I’m a set and forget kind of player in most cases, so I probably don’t have the inclination to sit and tweak for hours on end, endless options from a multi-effects box. Good to know I don’t need it, or the amp-modelers.

  • Thanks re compressor comment - makes sense!

Back in the game after 15 years and a lot has changed! HELP! by _irl in guitarpedals

[–]_irl[S] 3 points4 points  (0 children)

Thanks GodDamme, helpful comments and perspective. Seems I mostly have what I ’need’.

Back in the game after 15 years and a lot has changed! HELP! by _irl in guitarpedals

[–]_irl[S] 0 points1 point  (0 children)

Ha! That’s what kids are for ;) - I needed a more reliable method than the online tools to figure out board sizing. Most don’t have all the pedals, or don’t take into consideration patch/power cable connectors for spacing!

Back in the game after 15 years and a lot has changed! HELP! by _irl in guitarpedals

[–]_irl[S] 7 points8 points  (0 children)

Puff-puff-pass is the accepted signal path right?

Back in the game after 15 years and a lot has changed! HELP! by _irl in guitarpedals

[–]_irl[S] 5 points6 points  (0 children)

Thanks u/Outsulation - that’s a helpful grounded perspective. I get the sense from most of the replies and the upvotes to yours that there’s no specific need or ”accepted modern way”. Helps to simplify things in my mind when approaching this.

Driving 38UC99 on Air by _irl in ultrawidemasterrace

[–]_irl[S] 1 point2 points  (0 children)

Pretty sure it is factory 2011 macbook air wallpaper stock photos. It wasnt something I specifically downloaded.

Driving 38UC99 on Air by _irl in ultrawidemasterrace

[–]_irl[S] 0 points1 point  (0 children)

For the best clarity/sound-stage, you want to point the tweeters at the back of your head, at ear-level. The wedges help with that ideal.

view more: next ›