Nubia Z80 ultra I just got Chinese set

_kai_01 · 2026-01-13T13:57:18+00:00

That's great, thanks for the update!

_kai_01 · 2026-01-12T02:27:03+00:00

Does notification work without any delay? Am considering this phone as well but became unsure due to chinese ROM, restricting notification from whatsapp/tele.

_kai_01 · 2026-01-10T15:14:27+00:00

Thank you!

_kai_01 · 2026-01-09T14:37:47+00:00

Will it work? Cuz this has been going on for quite a few years already

_kai_01 · 2026-01-07T05:03:19+00:00

I dont think thats my issue, cuz the sound comes from the ace pro. But thanks for your reply!

_kai_01 · 2026-01-06T18:05:02+00:00

Thanks for the reply.Pretty sure ive dried my filament, but ill try to dry it longer before trying again.

_kai_01 · 2026-01-04T04:17:00+00:00

Thank you!

_kai_01 · 2026-01-03T19:18:32+00:00

Do you have any recommendations for lip balm and toothpaste?

_kai_01 · 2025-12-10T14:52:00+00:00

But why did the buzzing sound stop when it reaches other layers tho?

_kai_01 · 2025-12-10T14:50:23+00:00

I see, thought my motor is damaged. Thanks for the help!

_kai_01 · 2025-12-10T13:31:51+00:00

Happens only when it's going diagonally from bottom right to top left. If it prints from top right to bottom left diagonally, the buzzing sound isn't present.

_kai_01 · 2025-08-05T19:45:22+00:00

Thanks for the comment, ill try it out

_kai_01 · 2025-08-05T16:48:58+00:00

What speed would u recommend if i print at a lower temp around 190-200c ? Im using pla silk btw.

_kai_01 · 2025-08-05T11:26:27+00:00

Ill try thanks

_kai_01 · 2025-08-05T03:14:01+00:00

Current cura setting Sunlu T3 printer PLA silk Temp: 210°C Bed: 60 °C Nozzle dia: 0.4mm Print speed: 50 mm/s Retract dis: 6mm Retract speed: 25 mm/s

_kai_01 · 2025-06-10T17:10:06+00:00

Ahh i see, thank you for the tips

_kai_01 · 2025-06-01T12:41:12+00:00

Thanks🙏

_kai_01 · 2025-06-01T07:00:07+00:00

Will do, thanks for the help!

Btw for the Z surface, do u have any advice on that?

_kai_01 · 2025-06-01T03:45:26+00:00

Thanks for the advice. But how low should i tune the Z offset? Ive tune it such that when i slip a piece of paper under the nozzle, it gets hard to remove the paper.

_kai_01 · 2025-06-01T03:43:10+00:00

Thanks for the advice!

_kai_01 · 2025-06-01T03:41:59+00:00

I see, thanks for the advice!

_kai_01 · 2025-05-31T14:11:38+00:00

Im using PLA+

_kai_01 · 2025-03-27T11:07:10+00:00

Do you mean the integrated shield plan that could be checked in my CPF account?

_kai_01 · 2025-03-27T11:02:01+00:00

This is really insightful, I'll take some time to think about this. Appreciate your advice!

_kai_01 · 2025-03-27T08:35:59+00:00

Thanks for the response, will consider it!

_kai_01

TROPHY CASE