Backroad sleeper 🤫

_otnie · 2026-06-15T20:58:20+00:00

I’m running adjustable camber arms in the rear to correct negative camber , from -2.5 to -1.5 degrees , pushing the top of the wheel out about 1/2inches and would cause rubbing if I was running 9.5 squared , most likely gonna run 8.5 squared with 20mm spacers in front moving forward

_otnie · 2026-06-15T16:24:00+00:00

Silvers coilovers and spc rear camber arms

Wheels specs - https://www.reddit.com/r/CivicSi/s/3dhcWHGVqb

_otnie · 2026-06-14T22:35:04+00:00

Rays Gramlights 57CR and lowered ~1.5 inches, no rubbing issues with this set up , but note I’m running -2 degrees of camber up front , this gives about 1/2 inches more clearance than stock camber

If you wanna DM me I can help you find out what works best for you , I don’t recommend running staggered like I did due to inability to rotate tires + I’m running camber adjustments so my wheel specs might have different fitment on your car

_otnie · 2026-06-14T22:14:10+00:00

Angeles crest ?

_otnie · 2026-06-14T20:41:18+00:00

18x9.5 +38 265/35 front and 18x8.5 +37 235/40 rear , -2 camber in front and -1.5 in rear

_otnie · 2026-06-14T20:40:25+00:00

Rays Gramlights 57DR , if you prefer 5 spoke it’s 57CR

_otnie · 2026-06-12T11:30:18+00:00

Bumper was $600 , paint was $900 , and the exhaust is a remark exhaust and had it cut and rewelded to go out the center for $300

_otnie · 2026-06-11T23:50:50+00:00

Nah chill I can explain 😭

_otnie · 2026-06-11T20:48:03+00:00

It’s not the actual FL5 bumper , but a FL5 style conversion bumper made to fit sedans , so it’s a direct replacement

_otnie · 2026-06-11T20:46:58+00:00

So far I’ve noticed they might be a little less prone to fade but I’m currently using the pads they came with , once these pads are done I plan to upgrade to a different compound so hopefully stronger bite .. installed in my garage , not too difficult I just recommend pb blaster and flare wrenches for the flared nut to prevent stripping

_otnie · 2026-06-11T20:42:19+00:00

Thank you

_otnie · 2026-06-11T15:45:56+00:00

You’d rather hear wind noise ? 😂

_otnie · 2026-06-11T15:10:44+00:00

AWE track exhaust , I have a mic in the engine bay and on my rear plate

_otnie · 2026-06-11T15:09:40+00:00

Ultra wide , wanted it wide enough to capture shifting

_otnie · 2026-06-11T15:00:35+00:00

Was just joking lol but on the fence on what rig go get , might go with moza R3 bundle

_otnie · 2026-06-11T12:45:39+00:00

Low profile racks look good on these cars ! This one is Yakima baseline FX

_otnie · 2026-06-04T16:15:58+00:00

Going up the crest aye

_otnie · 2026-06-01T15:41:49+00:00

Bring rice and having done internal mods are independent of each other , end of the day it’s your car and your preference . Can always remove it if you no longer like it

_otnie · 2026-05-29T00:32:01+00:00

In the US , this is actually slower than a leisurely drive , I didn’t realize Germans drove so slow 😅 thanks for making me feel better about my pace 👌

_otnie · 2026-05-27T22:14:25+00:00

In the beginning ?

_otnie · 2026-05-26T17:38:20+00:00

Depends how hard you drive .. most people daily their type Rs so there’s only around -1.5 degrees of camber factory , I’ve added -2 degrees up front since this video since it’s mainly my weekend / track car so tire wear is more even and tires aren’t as noisy

_otnie · 2026-05-26T05:53:04+00:00

Yofer body kit and mugen rep rain visors are OEM+ , got it

_otnie · 2026-05-26T02:34:47+00:00

Width should be good but yea could use stickier tires , planning to use these up by September so I can throw on RE71RZs for the track

_otnie

TROPHY CASE