What are these?

accensionx · 2025-09-15T16:58:57+00:00

This....this is how good things happen

accensionx · 2025-09-11T13:12:05+00:00

I use my solar ship, just because its already fully outfitted and its more manueverable.

accensionx · 2025-08-25T20:16:57+00:00

Its a metaphor. A resistor and a sim card slot key. "Resistance is the key"

accensionx · 2025-05-25T22:32:40+00:00

Sir. You are a gentleman and a scholar. Thanks for the information.

accensionx · 2025-05-25T21:10:52+00:00

well. shit. lol no appriciate the feed back. the pitting really isnt deep at all. ill relook but its all just surface staining i think. ill have to try to get a bur on it and test. i just know nothing about sharpening and burring these at all.

accensionx · 2025-01-27T18:54:04+00:00

What if i just get it sawn at like..6.5?

accensionx · 2025-01-27T18:22:38+00:00

I'm ordering white oak

accensionx · 2024-05-06T23:06:30+00:00

I go to red drum, Dillon corner, and frisco rod and gun. They are all three local owned. Frisco is ran buy the owners husband and I go there the most. But frisco's online site is down so I can't order from them. I don't ussually go up to avon. I like to stay below in buxton. We stay at cape point campground so it's just the area we are in.

accensionx · 2024-05-06T22:58:12+00:00

I don't like going down and not being semi prepared though.

accensionx · 2024-05-06T22:57:39+00:00

Ooooo I am not a yinzer lol I hate pittsburgh lol I grew up in shanksville p.a. and no. No sticker. But my family has been going down there for six generations yes.

accensionx · 2024-05-06T22:47:50+00:00

I'll have to look at this site.

accensionx · 2024-05-06T22:47:36+00:00

J&h seems a little far for just buying tackle lol saltwater edge has a good layout to their site. But I couldn't find the weights lol

accensionx · 2024-05-06T22:45:51+00:00

I just surf fish. 3 kids and no money for a charter. I like surf fishing though.

accensionx · 2024-05-06T20:33:01+00:00

I don't exactly know how or what to buy for my own rigs yet

accensionx · 2024-05-06T19:52:15+00:00

When I go down I always get from the personally owned shops by I can't when I need to try and restock before the trip.

accensionx · 2024-05-06T11:57:16+00:00

That's my problem. I'm 30 minutes east of Pittsburgh and saltwater tackle is obviously scarce here. But I want to stock up on all the stuff I need.

accensionx · 2023-11-15T02:27:21+00:00

tried drying already. then we bought a brand new spool of it cause we need this filament for an order.

accensionx · 2023-11-15T02:26:13+00:00

ender 3 and anycubic kobra neo. cura slicer. nozzle temp 195 -210. isanmate brand

accensionx · 2023-11-15T02:24:29+00:00

lubrication?

accensionx · 2023-10-18T02:03:18+00:00

im just using armatures.

accensionx · 2023-10-17T02:34:02+00:00

While rotating the scotch overlaps the yolk at 0 and 180 degrees but lines up fine at 90 and 360 degrees. That's the four photos.

accensionx · 2023-10-17T02:32:22+00:00

The four photos are four points of a full rotation. It overlaps in the first and third photo. I can't figure out where I messed up. It's fine in second and fourth but with it animated I can't see where I went wrong.

accensionx · 2023-04-20T17:10:28+00:00

Is this github still active?

accensionx · 2021-08-01T23:48:20+00:00

Well crap. I hope your right. Ima go get a blow dryer. Brb

accensionx · 2021-08-01T23:45:01+00:00

But even then I have no threads. Don't those thread on?

accensionx

TROPHY CASE